£12.75 exc vat
£15.30 inc vat
In stock
Rover have changed the length now and picture shows original
PCH113760 top part of T section is 8.75" to 9" long and with lower bent outlet facing to the left, the top left is 2" long with 7" to the right- some were only 5" to the right so cut if required.
See part PCH10532 where the top part of the T is 8.75 long with both sides being nearly the same length, it has been adapted for use as PCH113760 on some vehicles.The bottom elbow section is the same on both but this part has a plastic joining scetion fitted making it an expensive part.
Measure up carefully before cutting using old hose as template
£12.75 exc vat
£15.30 inc vat
In stockRecommended usage 1 x PCH113760 to fit one mini.
T shape special hose for Single point injection cars only, from thermostat to inlet manifold and heater hose-
(221mm)8.75" long on top with the lower bent outlet facing to the left at the bottom, the left top part is (108mm)4 and quarter inc...
Original 7/16" spring type hose clip as used on later cars (approx 1990 on) for some radiator hoses and fuel lines.
MPI only. 3 YEAR GUARANTEE-UK made.Large impeller higher capacity water pump. Mini Spares procured product as original Rover Airtex tooling has been scrapped.
Fitted with a PPS, glass filled plastic impeller as used by Jaguar and Aston Marti...
3 YEAR GUARANTEE-UK made.Large impeller higher capacity water pump with top quality die cast body . Mini Spares procured product as the original superb Rover Airtex tooling has been scrapped.
Fitted with a PPS, glass filled plastic impeller...
3 YEAR GUARANTEE-UK made. Large impeller higher capacity water pump with a high quality die cast body. A Mini Spares procured product as the original superb Rover Airtex tooling has been scrapped.
Fitted with a PPS, glass filled plastic impe...
This electic radiator fan was fitted as standard on minis with the large round hole cut out in the inner wing fron 1991. On the 1275 Cooper last carb models there was an earler type fan which is also no longer available. As the original Cooper carb f...
This hose has the large outlet one end to fit the special thermostat housing
fitted to the Carb type Cooper.
2 plastic 5/8" outlets at the same end and close together which exit the heater on the r/h side. The later HIF38 1275 and single point cars had a change point where the plastic outlets exited on the l/h. This is a JEF10005.
These units take ...
Water hose pipe clip for the GRH1140 top hose and twin point injection cars which had larger hoses fitted .This clip will wind down to fit most radiator hoses if required.
Real Kevlar stranded hose,2 year guarantee-the only true Kevlar threaded hose available where you can see the strands, it is made for longevity and low heat transfer making this the best selling bottom hose in the market.
The built in proper...
Hose clip for 5/8" heater hose and used to locate 3/4" diameter anti roll bar in our C-AJJ4008 kit.
Sensor type Radiator that uses the original Rover clip in type sensor hole in the bottom which was fitted from 1991 up until the introduction of the twin point front mounted type.
This is a Cuprobraze 3 tube modern design version with 9 gill...
Clear plastic windscreen washer tubing sold by the metre only. This is the larger size and was known as 1/4" bore because GWW201M is 1/8" bore. This hose is actually now known as 4.8mm which is nearer 3/16".
this was known as 1/...
Thermostat 88 degrees. Fitted to 998 and 1275 minis from 1988 to 2000. Also Metros 1980 to 1990 998 and 1275.
Upper radiator hose for 850/998/1098cc Mini Mk2. This hose is shorter than the original Mk1 radiator, but fits all curent radiators where the radiator outlet is positioned 1-1.5" in from the outer edge.
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.