£90.00 exc vat
£108.00 inc vat
Out of stock
RACE quality bearing set being made at the Mahle Motorsport Race Bearing Division Vandervell F1 plant in the ...
£90.00 exc vat
£108.00 inc vat
Out of stock
These con rod bolt and nut set are made by ARP in the USA and considered the best available FITS 1300 con rods plus MGB late 18V engine numbers with 11-32" bolts. Quantity required one kit per car. torque up to 38-40lb ft.
Genuine part on sale at less than half price.
Most engine builders will tell you to replace the rod bolts as often as you can afford, but at least every other time you do the bottom end. If you don't know the last time, replace them. The [li...
Multi point big end journal nut for 1.75" bearing size con rods. These are multipoint nuts as fitted to Pre A plus engines. A Plus engines used CAM6263 which had the built in flange to spread the load but are not available. They are in...
You should replace the camshaft bearings every time the block goes to the machine shop. These bearings fit all late model 1275cc blocks (the ones without tappet covers on the back) It's almost too simple and thus often overlooked during a rebuild. Ca...
Mahle RACE quality std size main bearings for Pre A Plus 1275cc as used by competition engine builders.Quantity required-1 set.
RACE quality bearing set being made at the Mahle Motorsport Race Bearing Division Vandervell F1 plant in the UK...
Mahle RACE quality std size shells as used by competition engine builders.
for 1.75" big ends on 1275cc.
RACE quality bearing set being made at the Mahle Motorsport Race Bearing Division Vandervell F1 plant in the UK. This is an up...
Main bearings, 1275 2" mains. Heavy duty steel backed bearing for durability and long life. The bearings to use if you want it to last. The only bearings to use on a competition motor. Mahle manufacture..Quantity required-1 set.
Rod bearings, 850-1275 1 5/8" journals. Heavy duty steel backed bearing for durability and long life. The bearings to use if you want it to last. The only bearings to use on a fast road car.
( Tri-Metal )
Sintered copper lead, lead...
Block gasket set for all mpi cars (1997on).10 gaskets and 3 seals only
This expensive gasket set was Rovers answer to leaking A plus blocks on the MPI cars to save any warranty costs, using latest Klinger type gaskets where applicable to avo...
The oil pressure relief valve consists of an aluminum plunger with a heavy spring behind it. Access is through the 15/16" domed cap nut beside the dizzy. Once this nut is removed the spring will be visible. The plunger is beneath the spring and will ...
A series mini engine crank pulley bolts have been known to come loose, caused by pulley damper vibration on competition engines. This is a high tensile longer extended thread cap head bolt with thick washer to rectify this problem and also allow furt...
Rover piston TAM2048 stamped 21962 with ring sizes 1.501mm and oil ring 4mm but some pistons have been stamped 21963.
-Does this get confusing?
So lets clear it up; the easy way to identify the piston and corrrect rings are as follo...
Mini Spares own Universal gasket set for solid wall blocks
For any manual block, includes gaskets for "A"Plus and pre A Plus timing covers, but is less tappet chest cover gaskets. Does not include clutch oil seal.
We now offer an en...
Competition Slot drive pump for 1300cc A-Plus engines.
Almost all oil pumps available today have the same design capacity. The problem is the lack of precise manufacturing. Most factories in their quest for production volume have sacrificed ...
Cup type core plug for all cooper S only @ 41.4mm wide.
4 required per engine.
AE Hepolite +60 RINGS engine set C-AJJ3378/60-C-ajj3382-60 Mega and Omega pistons when rings are 0.0470(1.2mm) and 0.1575 4mm oil rings.
For latest spec NPRR race quality rings see C-STN102-20
Good maintenance, just as you would never rebuild your motor without replacing the crank thrust washers, you should also care about the camshaft thrust plate. Sometimes called the "triangle plate" this small but important plate doesn't just hold the ...
This is our racers favourite way of dealing with the worn or troublesome front primary gear bush.(this is NOT the top hat type rear bush)22.5mm wide. Racers and professional engine builders will use their own tolerances but these are set for road use...
The oil pump with a difference. This pump was designed as a long lasting modern oil pump. The steel backing provides rigidity and improved life expectancy. The two bolt design allows the use of this pump in any block configuration. The drive required...
Countersunk screw for holding the front palte to the crankshaft bearing cap on cars fitted with duplex gears to give the clearance required. 2 required per car.
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.