SELECTOR FORK ROLL PIN - ROD CHANGE
22G2595

($1.35) £1.35 exc vat

($1.62) £1.62 inc vat

In stockIn stock
special shaped roll pin for the rod change selector forks

($1.35) £1.35 exc vat

($1.62) £1.62 inc vat

In stockIn stock

Recommended usage 1 x 22G2595 to fit one mini.
Rod Change Gear Selectors and Speedo Drive - Qty 1
Gearbox Selector Forks - Qty 1

People also bought products
NEEDLE ROLLER 1ST MOTION / LAYSHAFT 4 SYNC
13H9513INA

High quality version of 13H9513, INA branded.



Dual use bearing fits the end of the A Plus 18mm mainshaft where the 1st Motion shaft slides on, plus it is used on the A Plus layshaft smaller end.



Kno...

($15.63) £15.63 exc vat

($18.76) £18.76 inc vat
IDLER NEEDLE ROLLER BEARING FOR A PLUS GEARBOX IKO
TUK100320-IKO

IKO idler gear bearing with special rollers for allowing movement on late type idler gears. The idler gears for twin point cars were also made from clean steel as an upgrade from 1996 on. This special bearing replaces the cheaper inferior earlier bea...

($7.20) £7.20 exc vat

($8.64) £8.64 inc vat
SPEEDO DRIVE SEATING BUSH SLEEVE - SECOND HAND
2A3624MS

Secondhand (used unit)only. This sits under the 28G251(DAM8488) alloy housing where the speedo cable connects to on the gearbox and the speedo drive pinion slots through this.Obsolete from Rover we are offering these old used units in ca...

($2.00) £2.00 exc vat

($2.40) £2.40 inc vat
PRIMARY GEAR BACKING RING GENUINE
88G549GENUINE

Genuine Rover spacer that fits up against the primary gear on the crankshaft and held on by the "C" washer 22A319 - both these parts wear as well as the gear.

Mini Spares also produce a ring 2 thou thicker 88G549 to...

($13.00) £13.00 exc vat

($15.60) £15.60 inc vat
DIFF HOUSING LOCK TAB ROD CHANGE LH
42H500

Left hand differential lock tab as used on rod change boxes up until 1982 when they were not longer used. For R/H locktab see 22A962

($0.91) £0.91 exc vat

($1.09) £1.09 inc vat
DIFF HOUSING LOCK TAB ROD CHANGE RH
22A692

Right hand differential lock tab as used on rod change boxes up until 1982 when they were not longer used.

($1.35) £1.35 exc vat

($1.62) £1.62 inc vat
GEARBOX LOCKTAB FOR 3 BOLT MAIN BEARING HOUSING/ S...
DAM6047

FITTED from 1984 on-single locktab for the 3 bolt main bearing(double roller)

housing and deleted 1996 on.locking glue used such as locktite

($0.99) £0.99 exc vat

($1.19) £1.19 inc vat
GEAR LEVER BUSH FLANGE
22G292

($5.63) £5.63 exc vat

($6.76) £6.76 inc vat
LAYSHAFT A PLUS PERFORMANCE
C-22A1739

Minispares were the first company to produce these layshafts for performance engine/gearboxes as the standard type would flex and resullt in the breakage of the bearings causing seizure. Produced in an upgraded material and heat treated to the correc...

($31.85) £31.85 exc vat

($38.22) £38.22 inc vat
3 SYNC 1st MOTION SINGLE ROLLER RHP/NSK
2A3709

Single roller bearing that only fits 3 synchro gearboxes to hold the 1st motion shaft-sporadic stocks only of these bearings as they went obsolete in 2008. These are genuine RHP/NSK bearings

($135.00) £135.00 exc vat

($162.00) £162.00 inc vat
THRUST WASHER LATE LAYGEAR .127-129"
DAM3182

($10.25) £10.25 exc vat

($12.30) £12.30 inc vat
LAYGEAR LATE TYPE OF 22G927 USED for 18mm bearing
DAM3169

USED ONLY-Laygear fitted to gearboxes with 18mm nose on layshaft for fitment with the 17 tooth 1st motion shaft. Basically a 22G927 with larger 13H9513 18mm bearing hole and usually has no identification marks.No warranty

($25.00) £25.00 exc vat

($30.00) £30.00 inc vat
SPEEDO DRIVE HOUSING COVER BOLT
DAM7761

3 of these bolt are used on the speedo housing gearbox front cover-they used to be 53K1474 studs 3.75" long but change to this bolt in 1985 3.25"long 5/16"unc

with tuflock patch to secure.

($2.08) £2.08 exc vat

($2.50) £2.50 inc vat
MAINSHAFT NUT UNF
22G48

Used on all mainshafts with 14mm shaft end for the 1st motion shaft---when they went to the 18mm shaft on A plus gearboxes they used DAM7485 which is metric thread.

($6.99) £6.99 exc vat

($8.39) £8.39 inc vat
BEARING FOR IDLER GEAR CONVERSION ROLLER A+ TO PR...
DAM3745

THIS BEARING HAS PRE A+ INNER DIAMETER AND A+ OUTER DIAMETER. If you have the large A plus idler gear bearing hole and want to use it for the earlier pre A plus small hole type idler gear then this bearing is what you require to sleeve it down in siz...

($15.50) £15.50 exc vat

($18.60) £18.60 inc vat
IDLER GEAR SHIM 134/.135" (YELLOW)
DAM4823

These are the later A+ type spec which rover superseded to when upgrading the idler gear material on injection cars. See workshop manual for shimming details

Quantity required is 2 per gearbox but the idler gear requires shimming for correct...

($16.80) £16.80 exc vat

($20.16) £20.16 inc vat
PINION "C" SHIM .004"
GUG705646GM

The shims go against the mainshaft double roller bearing securing cap in your gearbox to give it pre load. See workshop manual for advice but you are aiming for only 1 thou pre load.

($0.79) £0.79 exc vat

($0.95) £0.95 inc vat
IDLER GEAR SHIM .136/.137" (RED)
DAM4824

These are the later A+ type spec which rover superseded to when upgrading the idler gear material on injection cars. See workshop manual for shimming details.

The idler gear in all Mini power units must be set with great care. The thrust wa...

($16.80) £16.80 exc vat

($20.16) £20.16 inc vat
IDLER GEAR SHIM .136/7" BLUE
22A1548

Idler gear shims for the Pre A Plus gearboxes with 0.750" (19mm) size shafts

Quantity required per gearbox is 2 but idler gear shims require shimming for correct clearance 3-6 thou as per workshop manuals but 3 thou for road and 4 thou for r...

($13.50) £13.50 exc vat

($16.20) £16.20 inc vat
SINGLE ROW RHP ROLLER. 4 SYNCHRO
ADU7619

Genuine 1ST Motion shaft SINGLE track original bearing for 4 synchromesh 1st motion shaft.

This is a Genuine RHP bearing, and should not be confused with cheap alternatives. The cheap aftermarket bearings often fail and the work involved to...

($34.97) £34.97 exc vat

($41.96) £41.96 inc vat