($58.44) £58.44 exc vat
($70.13) £70.13 inc vat
($58.44) £58.44 exc vat
($70.13) £70.13 inc vat
Recommended usage 1 x R35960-20 to fit one mini.
4mm oil ring. These rings fit the current replacement pistons from AE Hepolite range 21250 and 21251 low drag slipper type with 8.1 cc dish and only piston 21251 is now available 8.8CR.
Rover piston TAM2048 stamped 21962 with ring sizes 1.50...
3mm OIL RING with compression ring size .0591" (1.5mm)and one piece oil ring .1181" (3mm)on p21253 pistons giving 9.7cr on 1275cc. 20 thou oversize
For performance see steel ring set with 3 piece oil ring as favoured by engine builders[link]...
Available at the moment but they sporadically become unavailable. Mini Spares have also had a batch of plus 60s specially commissioned to us for Grass trackers and racers. sold individually with rings and pin complete.
Ringsets are availabl...
20 thou oversize low drag slipper type pistons for modern day compression ratios and unleaded fuel.
Typically installation will result in a minimum 8.8:1 compression ratio but on some pre 1984 Metro versions it was higher.
Current...
NPR Ring set for 73.5mm Mega and Omega pistons with 1.2mm thick rings and 3 piece oil rings-also for new range of EVO pistons C-STN101
AE Hepolite +20 Engine set of rings for C-AJJ3378/20 C-AJJ3382-60 Mega and Omega pistons when rings are 0.0470"(1.2mm) and 0.1575" 4mm oil rings.
For latest spec race quality NPR rings see C-STN102-20
Sold as a single piston and although for Turbos is from original Rover casting and tooling to run on 5psi turbo boost. Now with 9.38cc. They use our mega ringset C-AJJ3379-40.
If using more boost you need to be working on a low...
AC Dodd Road Torque cam, great for low end power. Please see picture for full cam specs.
Road torque, this cam for strong low & mid range lugging, Touring, Smooth idle, excellent emmisions
ACD - RT
Power...
Replace with new camshaft,it's almost too easy to overlook during a rebuild. Camshaft bearings are pressed into the block and thus are usually done by a machine shop. You would not rebuild an engine without replacing the rod bearings, so why not the ...
Timing cover front plate and tensioner plate bolt and washer kit. Comes with all parts to fit the cover except for the counter sunk screws if fitting a duplex kit (our duplex kits all come with these).
You should replace the camshaft bearings every time the block goes to the machine shop. These bearings fit all late model 1275cc blocks (the ones without tappet covers on the back) It's almost too simple and thus often overlooked during a rebuild. Ca...
Set of +0.030" size 1275 crank thrust washers.
Set of +0.003" size 1275 crank thrust washers.
Mini Spares best quality complete gasket and seal kit for engine block and gearbox,for all common engine types and sizes.
Also comes complete with Mini Spares Evolution clutch oil seal 13H2934MS, differential oil seals...
ACL Race Bearings
ACL Race series bearings are precision manufactured to a wall thickness of ±0.0040mm giving engine builders close control of vertical oil clearance.
What is the purpose of ACL Race series bearings?
...
ACL Race Bearings
ACL Race series bearings are precision manufactured to a wall thickness of ±0.0040mm giving engine builders close control of vertical oil clearance.
What is the purpose of ACL Race series bearings?
...
ACL Race Bearings
ACL Race series bearings are precision manufactured to a wall thickness of ±0.0040mm giving engine builders close control of vertical oil clearance.
What is the purpose of ACL Race series bearings?
...
ACL Race Bearings
ACL Race series bearings are precision manufactured to a wall thickness of ±0.0040mm giving engine builders close control of vertical oil clearance.
What is the purpose of ACL Race series bearings?
...
ACL Race Bearings
ACL Race series bearings are precision manufactured to a wall thickness of ±0.0040mm giving engine builders close control of vertical oil clearance.
What is the purpose of ACL Race series bearings?
...