(6,10 €) £6.10 exc vat
(7,32 €) £7.32 inc vat
In stock
This tube uses the 12A116 dipstick which had a flat washer and just sat on top of the tube.
Not fitted to 850cc,997cc,or any A plus.
Fitted to 998/1098cc and all Cooper S models which later models usually had the metal tube originally, plus 1275 pre A plus
(6,10 €) £6.10 exc vat
(7,32 €) £7.32 inc vat
In stockRecommended usage 1 x 12G107 to fit one mini.
High quality silicone version of 12A1358. Fits all A series and A+ rocker covers.
Victor Reinz/Mahle small bore head gasket for A-series engines.
Gasket fitment. Writing side up.
Genuine Mini Spares engine front plate for pre A+ plus timing gear.
this fits engines using the early egg shaped cover
This plate has been modified by counter sinking the 2 main cap bolt holes to accept countersu...
Spring seat shims (set of 4), 0.020" thick (0.5mm).
Spacer shims to increase valve seat pressure and overall spring rate.
These were also used on all the 8 port head valve seats to prtect the alloy seats from wear. (8 port now C-AHT...
Spring seat shims (set of 4), 0.040" thick (1mm).
Spacer shims to increase valve seat pressure and overall spring rate.
These were also used on all the 8 port head valve seats to prtect the alloy seats from wear. (8 port now C-AHT36...
Timing cover front plate and tensioner plate bolt and washer kit. Comes with all parts to fit the cover except for the counter sunk screws if fitting a duplex kit (our duplex kits all come with these).
Mini Spares genuine upgraded part. Hexagon head rocker screw nut in EN24T.
Also available is a flanged nut C-AHT449
"used old"Distributor drive,all pre A Plus A series engines plus MGB.
Fitted in the engine block to drive the distributor these were made obsolete in 1988 by Rover so if you have lost yours we have a few of these used shafts to keep yo...
Genuine Bosch lambda sensor, fitted to both the twin and single point injection cars and fitted in the same exhaust manifold shared by both cars. Be warned the cheaper non branded sensors cause lots of issues hence we only sell the Bosch version.
Fitting kit comprising of studs, nuts, plain washers, spring washers and a gasket
Replacement O ring for the Minispares range of chrome dipticks
This kit of head studs is the best available for road and lightly tuned engines. See the C-AHT280 set for highly tuned engines.
The material spec is alloy steel heat treated to 75 tensile tons per square foot minimum and finish...
You should replace the camshaft bearings every time the block goes to the machine shop. These bearings fit all late model 1275cc blocks (the ones without tappet covers on the back) It's almost too simple and thus often overlooked during a rebuild. Ca...
Race quality Single piston ring pack for Mini Spares Evolution Pistons which also fits Mega and Omega pistons. This uses 3 piece oil ring 4mm and 2 of 1.2mm compression ring--sold per piston so 4 packs required per engine
Stabiliser bush kit for lower engine steady
ARP Head stud kit that compromises of;
4 x Long Head Studs
7 x Short Head Studs (Disregard 2 if you're using a 9 stud application)
11 x Multipoint ARP nuts
11 x Heavy Duty Washers
4 x Rocker post studs <...
Mini Spares best quality complete gasket and seal kit for engine block and gearbox,for all common engine types and sizes.
Also comes complete with Mini Spares Evolution clutch oil seal 13H2934MS, differential oil seals...
ACL Race Bearings
ACL Race series bearings are precision manufactured to a wall thickness of ±0.0040mm giving engine builders close control of vertical oil clearance.
What is the purpose of ACL Race series bearings?
...
ACL Race Bearings
ACL Race series bearings are precision manufactured to a wall thickness of ±0.0040mm giving engine builders close control of vertical oil clearance.
What is the purpose of ACL Race series bearings?
...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.