(0,59 €) £0.59 exc vat
(0,71 €) £0.71 inc vat
In stock
The 6 longer ones are 22A152.
These studs are also used as manifold studs on Mini spares alloy heads. Sold individually.
(0,59 €) £0.59 exc vat
(0,71 €) £0.71 inc vat
In stockRecommended usage 3 x 53K547 to fit one mini.
Flanged head short UNC 5.16" BOLT for flywheel casing 1.0625"long it was used as an alternative to DAM7755 which was only 1" Long with tuflock patch to secure-this will be discontinued by Rover when current stocks are gone.
The original Special Tuning head 8 port head by Jim Whitehouse is the ULTIMATE Push rod head for the "A"Series but is NOT A STRAIGHT BOLT ON PART.
It is supplied fully assembled with springs/top caps,Evo collets and utilizes the original siz...
Amal carburettor kit for the Arden 8-Port head. Complete with carbs, manifolds and linkage.
Hi spec all new alloy 5 port gas flowed head. Outright sale to save you the risk of losing £240 on exchange schemes where old heads are traded in and where faults are found, especially by some companies.
Speak to York branch for all modifica...
The original Special Tuning head 8 port head by Jim Whitehouse is the ULTIMATE Push rod head for the "A"Series has now been revamped and made available with larger inlet valves and special seats available to special order.Ports and combustion chamber...
Complete bolt kit to bolt the transfer case and clutch cover onto the engine block.
Very Hi spec all new alloy 5 port super gas flowing head. Outright sale to save you the risk of losing £240 on exchange schemes where old heads are traded in and where faults can be found, especially by some companies.
The C-AHT347...
Very Hi spec all new alloy 5 port super gas flowing head. Outright sale to save you the risk of loosing £240 on exchange schemes where old heads are traded in and where faults can be found, especially by some companies.
C...
Left hand differential lock tab as used on rod change boxes up until 1982 when they were not longer used. For R/H locktab see 22A962
Right hand differential lock tab as used on rod change boxes up until 1982 when they were not longer used.
FITTED from 1984 on-single locktab for the 3 bolt main bearing(double roller)
housing and deleted 1996 on.locking glue used such as locktite
Solid dowel at the front of the engine that locates the block to gearbox.
Minispares were the first company to produce these layshafts for performance engine/gearboxes as the standard type would flex and resullt in the breakage of the bearings causing seizure. Produced in an upgraded material and heat treated to the correc...
Single roller bearing that only fits 3 synchro gearboxes to hold the 1st motion shaft-sporadic stocks only of these bearings as they went obsolete in 2008. These are genuine RHP/NSK bearings
3 of these bolt are used on the speedo housing gearbox front cover-they used to be 53K1474 studs 3.75" long but change to this bolt in 1985 3.25"long 5/16"unc
with tuflock patch to secure.
Used on all mainshafts with 14mm shaft end for the 1st motion shaft---when they went to the 18mm shaft on A plus gearboxes they used DAM7485 which is metric thread.
THIS BEARING HAS PRE A+ INNER DIAMETER AND A+ OUTER DIAMETER. If you have the large A plus idler gear bearing hole and want to use it for the earlier pre A plus small hole type idler gear then this bearing is what you require to sleeve it down in siz...
These are the later A+ type spec which rover superseded to when upgrading the idler gear material on injection cars. See workshop manual for shimming details
Quantity required is 2 per gearbox but the idler gear requires shimming for correct...
The shims go against the mainshaft double roller bearing securing cap in your gearbox to give it pre load. See workshop manual for advice but you are aiming for only 1 thou pre load.
These are the later A+ type spec which rover superseded to when upgrading the idler gear material on injection cars. See workshop manual for shimming details.
The idler gear in all Mini power units must be set with great care. The thrust wa...
Idler gear shims for the Pre A Plus gearboxes with 0.750" (19mm) size shafts
Quantity required per gearbox is 2 but idler gear shims require shimming for correct clearance 3-6 thou as per workshop manuals but 3 thou for road and 4 thou for r...
Genuine 1ST Motion shaft SINGLE track original bearing for 4 synchromesh 1st motion shaft.
This is a Genuine RHP bearing, and should not be confused with cheap alternatives. The cheap aftermarket bearings often fail and the work involved to...
Full rebuild kit less diferential parts.
Using only the original manufacturers of the bearings such as RHP because all the Budget bearings are not good enough for longevity or performance use.
This is a full kit of bearings except...
This little roller bearing goes inside the end of the 1st motion shaft on minis with 14mm mainshaft which it sits on.
This bearing was previously part number 88G409 and a true Rover replacement, but if you have earlier A type gears with the...
Mini Spares Performance Baulk ring.
The standard sintered baulk (synchro) rings are not tough enough for the demands of performance useage, in many instances lasting only one race before failure or breakage. The main reason is the incompat...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.