(11,17 €) £11.17 exc vat
(13,40 €) £13.40 inc vat
In stock
(11,17 €) £11.17 exc vat
(13,40 €) £13.40 inc vat
In stockRecommended usage 1 x AEG248 to fit one mini.
A true Cooper S engine has 10 studs and one specially designed bolt. The ARP version of the stud is a 12 point design that matches the head stud kits (which come in either 9 or 11 stud.) Best of all, the ARP bolt cost less than the standard item!
This kit of head studs is the best available for road and lightly tuned engines. See the C-AHT280 set for highly tuned engines.
The material spec is alloy steel heat treated to 75 tensile tons per square foot minimum and finish...
Complete stud, nut and washer kit for the cylinder head ancillaries. Kit contains parts to retain the following:
Inlet/Exhaust manifold to head, studs/nuts/washers
Thermostat housing (no sandwich plate) studs/nuts/washers
H...
This thermostat housing fitting kit, suitable for all single tier thermostat housings. Comes with new studs, nuts, washers and Klinger thermostat housing gasket
replacements in stainless steel for the heater tap elbow on the cylinder head.
Quantity required one kit per car
Chrome Rocker bolt with UNF thread. Original Rocker cover bolts are dull zinc coated or painted but the chrome type look much better and cheaper.
A longer threaded version CAM6823 was used on prestige Minifin alloy type A series...
This 5/8unf steel hexagonal head blanking plug was made for the inlet manifolds where the servo union can be fitted, plus blanking off the thermal transmitter hole under the thermostat. Uses 1B3664 washer ----------please note this will ...
A simple way to dress up that engine compartment while at the same time insuring all the proper hardware is in place. A kit includes 2 each of British made chrome sleeve nuts, spacers and special cup washers, Fits all A & B series engines.
F...
Manifold stud 39mm long for all A series engines up to injection which use LYR10028 which is 6mm longer at 45mm.
Special extra long nuts were used on some manifolds. These nuts are about an inch long for easy reach and made of brass so they'll never corrode. Especially handy on the inner two studs on dual carb set-ups.
Sold singly and usually 2 used f...
This kit of head studs is the best available for road and lightly tuned engines. See the C-AHT280 set for highly tuned engines.
The material spec is alloy steel heat treated to 75 tensile tons per square foot minimum and finish...
Probably the most changed stud on the mini. This is the length used on every A series engine until the introduction of the sandwich plate when longer ones were required. A stainless steel variety C-STR286 is available which we do recomme...
You require 5 of these high tensile short head studs and they torque to 42lb/ft. See also complete kit which includes these top grade studs C-AHT279. 3/8"unc stud with unf end for head nut and is 4" long. See other long head stud [link]C...
The intake/exhaust manifold should be secured to the head with brass nuts and these very thick washers. These washers are intended to not only spread the clamping action but the thickness allows them to absorb the heat without deforming! Takes 4 per ...
Rocker covers should be held down by a nut with a washer to cover the seal and then this spacer. Available in chrome as a set SAC71L.
The proper washer is required to retain the rubber seal on the valve cover. For the complete hardware kit see SAC71L.
latest headnut with built in shoulder to help clamping pressure,Buying this kit of 10 for Cooper S 11 stud heads is cheaper than buying items seperate
Standard A-series cylinder head retaining nut. For the later flanged nut see part number CAM4545.
Heater valve studs fitted to the cylinder head. 1/4"unf 1.1250" long.
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.