(60,00 €) £60.00 exc vat
(72,00 €) £72.00 inc vat
(60,00 €) £60.00 exc vat
(72,00 €) £72.00 inc vat
Recommended usage 1 x C-AEG488 to fit one mini.
Accelerator bracket for twin carb models, mounts to inlet manifold.
Manifold gasket fitted to all A series pre 1992 except Turbo which had a reinforced exhaust ports GUG704063MG and SPI from 199. From 1991 on a new better gasket with reinforced exhaust ports and backing was fitted GUG704053MG
Manifold to carb gasket for HS2 single and twin carbs, usually 3 per carb required.
Special reinforced gasket for injection cars has metal inserts on exhaust ports plus a metal back on the manifold side which makes surface easier to clean when replacing. Often used on Turbo cars when correct gasket is in short supply.
...
This 5/8unf steel hexagonal head blanking plug was made for the inlet manifolds where the servo union can be fitted, plus blanking off the thermal transmitter hole under the thermostat. Uses 1B3664 washer ----------please note this will ...
Aftermarket union for fitting all mini inlet manifolds where a take off is required for your brake servo or emission valve on Cooper S cars.
The intake/exhaust manifold should be secured to the head with brass nuts and these very thick washers. These washers are intended to not only spread the clamping action but the thickness allows them to absorb the heat without deforming! Takes 4 per ...
Locating rings originally made for 12G295 heads with twin carbs to line up the inlet manifold to the inlet ports on the cylinder head it found its way on most twin carb factory produced cars. There is a recess in the inlet port on the he...
Manifold gasket fitted to all A series pre 1992 except Turbo which had a reinforced exhaust ports GUG704063MG and SPI from 199. From 1991 on a new better gasket with reinforced exhaust ports and backing was fitted GUG704053MG
Genuine mini Spares inlet manifold dyno tested and designed for our Stage one kit C-STN17. The single SU manifolds is developed to give maximum airflow and gas speed, yet fit all engines even if the standard air cleaner set-up is used. I...
Spacer block between carb and manifold for single HS2 carb. To use on twin carbs the fixing holes need drilling out to size. 7.5mm thick
Cast alloy type, Fits either twin HS4 or HS6.(requires modifacation to fit HS6.2 extra studs per carb)
This intake manifold for twin SUs has been carefully produced to minimize cross-port-flow interference caused by t...
Manifold stud for all A series injection engines and some late carburettor cars which is 45mm long-6mm longer than 53K487.carburettor engines usually retained the 53K487 shorter screw for the outside 2 holes.
Sold singly,6 per c...
This is the original type of needle valve that governs the plastic fuel float in your SU carb.
An alternative better upgraded version is available as CA90.
The new adjustable height StayUp® Float is resistant to modern ethanol based Fuels and has a military spec closed cell construction making it puncture proof. The ability to adjust the Float Arm allows for quick and easy minor alterations to Float lev...
Return spring kit for HS4 carburettor spindle.
Standard bore LCB (1-3/4" id) for standard to high performance 1275s and for street 1380s. This is the same manifold as the standard C-AEG365 but with a slightly different shape to allow fitment to cars fitted with rubber coupling drives...
Small hose clip for 1/4" fuel line (our part number PETROLPIPE)
This is the clamp on the cooper freeflow manifold to clamp it to the engine for extra support, supplied with tag.
Standard bore road LCB (1-3/4"id) that has an enlarged and reshaped middle pipe which creates a type of vortex, simulating a pulsing effect similar to the outside two pipes,thus producing an improved BHP,Torque and power curve.Ideal for very hot smal...