(1 159,23 €) £1 159.23 exc vat
(1 391,08 €) £1 391.08 inc vat
In stock
(1 159,23 €) £1 159.23 exc vat
(1 391,08 €) £1 391.08 inc vat
In stockRecommended usage 1 x FZX3054 to fit one mini.
Cast alloy type, Fits either twin HS4 or HS6.(requires modifacation to fit HS6.2 extra studs per carb)
This intake manifold for twin SUs has been carefully produced to minimize cross-port-flow interference caused by t...
New Carb Spacer for HS4 carbs with vacuum take off. 7.5mm thick.
The rod with the plate is called the butterfly rod and was fitted to all Cooper twin carb HS2 set ups.
Accelerator bracket for twin carb models, mounts to inlet manifold.
Before the days of Aeroquip, Minis were fitted with braided steel rubber fuel lines. They should be used in place of rubber for all fuel lines in the engine compartment. They come made to length, with rubber end caps.
If you need the 5/16...
This is the left hand linkage lever that sits on the rods between HS type twin carbs.sold individually
Gasket for an HS4-carb and manifold .Sold seperately and order as required for your car(usually 3).
Pin to hold the accelerator cable which locates in the carb bracket lever. Supplied as originally fitted with washers, nut and split pin plus a proper machined hole for the cable unlike many others on the market- which come either bare or with wrong ...
original shape of petrol feed pipe for twin HS" carbs as fitted to all the Coopers
This is the right hand linkage lever taht sits on the rods between HS type twin carbs. Sold individually
Probably the most changed stud on the mini. This is the length used on every A series engine until the introduction of the sandwich plate when longer ones were required. A stainless steel variety C-STR286 is available which we do recomme...
Throttle return springs for all twin carb variants. Usually 3 fitted.
Small hose clip for 1/4" fuel line (our part number PETROLPIPE)
Fuel or water T piece adaptor
used when upgrading fuel system size on specials from 1/4" to 5/16" or any other modifications
This tool/gadget allows you to balance both air intakes on either twin SU or twin choke carbs so they flow exactly the same to give better performance and economy.
Special rubber hose 1/4" bore for use on petrol lines, this is in black and not armour plated outside but does have internal reinforcing. Supplied as pre cut 1m length with 2 clips and is safe to use with modern fuels with higher ethanol content. SAE...
Before the days of Aeroquip, Minis were fitted with braided steel rubber fuel lines. They should be used in place of rubber for all fuel lines in the engine compartment. They come made to length, with rubber end caps. 1/4" bore size.
Orange ...
Our heavy duty throttle cable is superior in many ways.
A nylon interior ensures smooth operation. The outer cable is 32mm longer and inner is 95mm longer than the standard one.
Cable to carb bolt is ACC5062.
A very usefull tuning needle for single and twin carbs when camshaft change for carbs with floating needles.
Correct and original thickness oil for SU carb dashpots.
Stainless steel twin HS4 heatshields kit. Comes with Link bar and springs.
The favourite and best needle for Minispares stage one kit. Tested on a rolling road by Peter Baldwin this baby gave the best performance when using our RC40 system, Minispares inlet and exhaust manifold plus a K&N filter.
If us...
Complete with screw the choke trunnion is used on nearly all SU carb linkages.
See ACC5062 for carb cable link trunnion also.
These screws fit all HS type carb butterflies to hold them on the throttle spindle
Used in petrol fuel lines to take 1/4" petrol hoses it is used mainly on twin carb set ups for petrol being diverted to the 2 carbs.
Locating rings originally made for 12G295 heads with twin carbs to line up the inlet manifold to the inlet ports on the cylinder head it found its way on most twin carb factory produced cars. There is a recess in the inlet port on the he...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.