(9,45 €) £9.45 exc vat
(11,34 €) £11.34 inc vat
In stock
850/998/1100. If you require inlets see TAM2152.
Fitted from 1988 with introduction of press fit high compression pistons although many earlier heads have used this modification.
Recess required is 1.1245"(28.56mm) plus or minus 0.0005"(13mm)and 0.190" (4.83mm)deep at room temp of 20C
(9,45 €) £9.45 exc vat
(11,34 €) £11.34 inc vat
In stockRecommended usage 4 x TAM2068 to fit one mini.
Approx 23.5cc combustion chambers for use with dished pistons. This specification of cylinder head is the only modified version for the small-bore based engines Mini Spares supply as it is judged to be the only one worth up-grading to. Based on used ...
24.5-25.5cc combustion chamber for use with flat top pistons. This specification of cylinder head is the only modified version for the small-bore based engines Mini Spares supply as it is judged to be the only one worth up-grading to. Based on used c...
New competition valve cotter for early heads with the large single groove valve, these are precision CNC machined from 4340 and heat treated to a better spec than EN24T and claimed to be stronger in fatigue life.
These locate better in the v...
New competition valve cotter, these are precision CNC machined from 4340 and heat treated to a better spec than EN24T and claimed to be stronger in fatigue life.
These locate better in the valves and easier to control spring heights.
Genuine Mini Spares valve stem oil seal manufactured with original Dupont Viton, as fitted to the twin points engines, are the best material and seal you can use and although expensive are the best to date in stopping the engine smoking.
Man...
EXHAUST VALVE 1.15 TURBO
.3135 thou (7.96mm) thick, uses CAM6573 collets only.
Sold individually.
To help rocker pad to valve stem alignment and reduce friction, the standard springs can be replaced with solid spacers and correctb shim set. The spacers and shim kit are sold as C-AEG392.
Spacers for under the rocker pedestals are used mainly by engine tuners to allow tappet adjustment to be made where cylinder head mods have been carried out. 1.3mm/0.0512" thick, this can be used to hold locating screw on rocker post assembly but the...
Early Large cotter groove exhaust valve. Most small bore engines seem particularly prone to burning valves, it is highly recommended to replace the exhaust valves when you do a valve job! This 1.0" valve fits most early 948cc, 998cc and 1098cc engine...
1.311" (33.3mm) dia x 3.57 long intake valve.
Our race valves are produced in EN214N steel and rquire Manganese/Silicon bronze alloy valve guides. use the later narrow, single collet groove and current valve head shapes.
As ...
1.401" dia x 3.52" long intake valves. Our race valves are produced in EN214N steel, stellite tipped and use the later narrow collet groove and current valve head shapes. As it is possible, even common, to swap one head for another on 1275 engines, i...
Genuine Mini Spares product as everything else on the market was poor fitting and unstable.
For Performance see 88G459EVO made in the USA by a Specialised Racing product company.
All the earlier heads used the 2A11 cott...
Actually 29.3mm (1.15") these valves are in EN214N steel with chrome plated stems for use in standard iron guides. Easily noticeable by their strange design shape they claim to give better flow characteristics.
Collet for the 3 groove valve. Sold per half and 2 required per valve.
These cotters go with AHU1897 top cap. On Turbo heads after engine number 102641 were fitted on the inlet only.
All early 850/997/998/1098cc heads u...
If you drive A-Series cars long enough you will eventually have to replace the water pump bypass hose. These are the best quality available to fit without removing the cylinder head but these fluted rubber hoses have a bad reputation so if possible ...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.