(251,76 €) £251.76 exc vat
(302,11 €) £302.11 inc vat
In stock
Main and dash loom only.
(251,76 €) £251.76 exc vat
(302,11 €) £302.11 inc vat
In stockRecommended usage 1 x YMC120890 to fit one mini.
To convert a standard UK spec Single Point Injection car to HIF44 carb. This kit includes wiring looms,fuel tank,fuel pump, carb, air filter and inlet manifold.
Rear loom for 1992 on carburettor cars with a 13 way Econoseal plug.
Rear body harness with speaker wires, known as thin wall PVC covered wire type in FROM 1989 and occassionly fitted or found on early cars wothout any problems.
All rear body looms are OBSOLETE from Rover but we can get them made up...
Best on the market, sports coil-Not Lucas. A standard coil can only do so much, and when compression is raised (as in most high performance engines) or improper fuel mixtures occur something better is needed. This sports gold coil with proven origina...
Auxilary wiring for genuine Rover spot and fog lamps needed when fitting genuine lamps to cars not originally fitted with auxilary lamps or for cars that have had the wiring damaged. This loom is supplied with complete lamps XBN10008 and...
Main wiring loom with dim dip. Fits all 1275 cars with HIF38 carb from 1991-1994. No alarm.
Main and dash loom only.
Rear body harness with speaker wires,known as thin wall PVC type type which replaced the thick wall type in 1989. AN166 is the thick wall early equivalent.
If your car has no speakers just disregard the extra wires. This loom ha...
Electronic Ignition distributor, fitted as standard to all 1300 Carb Cooper models. Also Metro 1275cc engine.
Replacement service items for this are:
Cap GDC156
Rotor arm GRA2143
Should be used with GC...
Replacement Distributor ignition module fitted to all standard electronic ignition distributors (non injection) looking at the front of module, negative is on the left. positive on right and centre pin is not used.
The best chrome type available with screw and washer.
A headlight trim ring is only the starting point of a good looking car, but you have to start somewhere. Sold singly 2 required per car. These are the original type chrome over solid bras...
Rear fog lamp switch with the orange illumination segment for all vehicles fitted with production fog lamps as standard. 3.1cm tall from 1976 on.
Metal plate switch carrier for 5 square type switches.
This is the plug that fits all Mini alternators, except MPI. The three conections are alternator output, 12 volt sense and ignition lamp. Ideal when converting from a dynamo.
This is the latest model fuse box as used on all Minis after 1976 and all MG Midget/Sprites with 1275cc. Simple and easy to replace or upgrade from the earlier version. This box has the added advantage of having 4 fuses in place of the earlier vers...
Minispares design heavy duty STAINLESS STEEL spotlight bracket, for fitting to cars where it mounts on the front panel valance and grille support panel, giving it perfect rigidity so that the power of the lamp was not impaired. Many cheap aftermarket...
Two of these plastic lens that hold festoon bulbs (GLB239) are mounted in the metal cast number plate housing (13H6900) on all MK3 bootlids from 1970on. Sold individually with bulb LESS FIXING SCREWS.
See PMZ206 for screw replac...
All Minis require an earth strap from the engine to the body and from 1959-1996
they fitted from the gearbox to the subframe. When they introduced the twin point in 1996 it was moved to the upper engine stabiliser arm. About 13"LONG.
Rotor arm for all A series electric distributors when points are not fitted, except for turbo. The distributor cap for this rotor arm is GDC156.
White lens kit 1988 on. If your front indicator lens is held on by screws then this is the kit for your car with the side wing repeater lens also and correct orange bulbs.
If your front lens is held on by the chrome retaining ring as per all...
An ariel that mounts under the wing for minis. Beware when fitting 13" wheels as Rover moved the ariel to the roof.
Brake light switch for pre 1976 minis with single line brake systems. Fits into banjo bolt (7H7995) located at O/S front brake hose. This switch has a tapered thread. Made by a UK company who suplied parts to Unipart.
For minis ...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.