Original shaped one piece front to rear hydrolastic pipe for the right hand side. See also FSP3 and FSP4 alternatives.

£61.50 exc vat

£73.80 inc vat

FRONT BRAKE HOSE AND CLUTCH HOSE LARGE SHAKEPROOF ...

This special shake proof washer should be replaced. Found on front hose.

Also used on 21A1524 hydrolastic pipe adaptor.

£0.45 exc vat

£0.54 inc vat

HYDROLASTIC FLUID

MORRIS05

The term 'hydro' in the renowned Cooper "S" suspension system "Hydro-lastic" means at least in part a liquid. This famous system was designed by BMC make for smooth and fluid ride while taking all of the abuse of off road rallying. It is not uncommon...

£35.25 exc vat

£42.30 inc vat

HYDROLASTIC ELBOW NUT

17H8236

Nut to fit 21A1524 adaptor on end of front hydrolastic pipe and 21A1519 rear elbow. Sold singly 1 required each side of front and rear hydro suspension (4 in total per car).

£1.82 exc vat

£2.18 inc vat

HYROLASTIC EASY BEND 2 PIECE PIPE

FSP4

Made from easy bend metal but in two sections to make easier fitment.

Originals are available as 21A1575/7

£57.75 exc vat

£69.30 inc vat

BALL JOINT EXTRA SHIM KIT (6 SHIMS)

2A4242

Replacement ball joint shims, comprising of 2x 003"(.076MM) shims, 2x 005"(.127MM) and 2 x 010"(.254MM).

£2.48 exc vat

£2.98 inc vat

TIE BAR BUSH - HARD RUBBER SINGLE BUSH ONLY

C-STR628

Tie rod extra hard rubber bush, harder than standard.

You dont want these bushes too hard as it can cause the threaded on the end of the tie rod to break under extreme conditions.

In theory the outer ones should be harder for rigidi...

£1.05 exc vat

£1.26 inc vat

REAR HUB LESS STUDS TO FIT ALL MODELS

RLH10021

All models of the Mini use the same rear hub (this piece holds the rear wheel bearings). The Mini's rear wheel bearings are more than adequate, usually requiring only occasional repacking with grease. The weak link may be the cast iron hub; it is not...

£26.00 exc vat

£31.20 inc vat

GREASE NIPPLE TOP ARM (45°)

UHN445

Angled grease nipple for the upper arm on the front suspension of all Minis

importantly lubricates the upper arm spindle which so often gets neglected so check yours out and make sure this nipple is working properly. Also fits rear radius ar...

£0.85 exc vat

£1.02 inc vat

RADIUS ARM REPAIR KIT

GSV1125

Complete rebuild kit for rear radius arm as sold by us since 2005.

Beware of cheap imports that are available in the market as they do not have correct heat treatment where required and have no longevity.

Kit Includes: shaft, beari...

£9.98 exc vat

£11.98 inc vat

HYDROLASTIC FLUID

MORRIS05

The term 'hydro' in the renowned Cooper "S" suspension system "Hydro-lastic" means at least in part a liquid. This famous system was designed by BMC make for smooth and fluid ride while taking all of the abuse of off road rallying. It is not uncommon...

£35.25 exc vat

£42.30 inc vat

UPPER ARM REPAIR KIT

MSK001

Mini Spares own to original drawing specifications with heat treatment correctly applied where appropiate.Lack of proper maintenance (grease) will make the pivot shaft and/or bearings wear that much faster. In severe cases the shaft may rust to the b...

£12.81 exc vat

£15.37 inc vat

UPPER ARM THRUST WASHER

2A4326

Fitted on the retaining plate side of the upper arm spindle this washer is 7.4mm wide and is also provided in the repair kit MSK001. The washer at the other end is 2A7324 which is 3.8mm wide

£6.05 exc vat

£7.26 inc vat

RADIUS ARM SHROUD R/H

14A6615

Mini Spares product from own original tooling since 1989.This small sheet metal panel mounts below the horizontal seam, covering the pivot pin of the R/H rear radius/trailing arm.

This shroud uses 14A7091 rubber plug not suppl...

£6.30 exc vat

£7.56 inc vat

TIE BAR ROD COMPLETE FOR FRONT SUSPENSION (SINGLE ...

8G4249

The front tie rod on the Mini controls the fore and aft location of the lower front suspension arm of the car. In addition it provides a great degree of stability under braking. If your rod is bent or the bushes are worn then you need help. The Tie r...

£14.40 exc vat

£17.28 inc vat

HYDRO UNIT GAITER

21A1496

The weathered and cracked rubber you see is not actually the hydro displacer bag, but rather this rubber boot to protect it. Sold singly 1 required per displacer.

£12.00 exc vat

£14.40 inc vat

FRONT HYDROLASTIC BUMP STOP

21A1598

For Hydrolastic suspension cars, they were made with a 1/4" fixing hole but this needs elongating vertically to get the bump stop to sit properly on the upper arm which had different machine tolerances when manufactured.

£10.50 exc vat

£12.60 inc vat

HYDROLASTIC SLEEVE RETAINER PLATE FRONT SUBFRAME

21A1487

Have you got one of the rare "wet" suspension Minis? This is the retainer plate that holds the protective sleeve around the hydro hose on the bulk head panel.

Sold singly 2 required per car.

£3.45 exc vat

£4.14 inc vat

1.5° NEGATIVE CAMBER LOWER ARMS

C-AJJ3364

Sold in pairs only.

These arms will give an extra 1.5 degrees extra negative camber over what the standard arms give on your car. To correct all variations of incorrect geometry found on the mini we have produced a pair of on car adjustable ...

£45.00 exc vat

£54.00 inc vat

LONGER COMPETITION TRACK ROD END

C-AJJ1572

Longer track rod end for running with negative camber, gives an extra 5mm of adjustment approximately over the standard item. Has consistent thread pattern and perfect design to our requirements to fits all known racks and classed as a competition tr...

£7.92 exc vat

£9.50 inc vat

HYDRO QUADRANT SPRING WASHER

2K2545

special double coil spring washer which fits on the rear hanbrake quadrant on Hydrolastic cars only.Known as a thackery washer

£0.39 exc vat

£0.47 inc vat

WASHER FOR SHOCK ABSORBER DAMPER

AJD7162

Fits top and bottom of the front damper and the lower rear damper to keep the bush from moving in the damper (shock absorber) eye sockets. 3/8"hole.

1.4mm thick by 24.6mm wide.

£0.22 exc vat

£0.26 inc vat

ST BUMP STOP RUBBER

AHH7074

Same bump stop as fitted to MGB, this was utilised by ST Works Abingdon to go on their bump stop kits C-AJJ3313/4007 for hydrolastic minis. Sold singly.

£6.10 exc vat

£7.32 inc vat

REAR HUB OIL SEAL

GHS102

For the front wheel bearings of the Spridgets, rear of the Mini.

£1.24 exc vat

£1.49 inc vat

REBOUND BUFFER HYDROLASTIC. FLAT BUMP

21A1517

This is the flatter type rear rebound rubber on hydrolastic cars, uses exactly the same metal base plate as 21A1520 which is the larger cone type which is the bump stop rubber.

£4.49 exc vat

£5.39 inc vat