£1.00 exc vat
£1.20 inc vat
In stock
5/8 UNF grub screw that use 8mm allen key for blanking inlet servo take off or temp transmitter hole at front of pre 1996 cylinder heads. Can also use ADP210
£1.00 exc vat
£1.20 inc vat
In stockRecommended usage 1 x 5-8UNF to fit one mini.
This 5/8unf steel hexagonal head blanking plug was made for the inlet manifolds where the servo union can be fitted, plus blanking off the thermal transmitter hole under the thermostat. Uses 1B3664 washer ----------please note this will ...
35.7 x 29.5mm race valves in plasma-nitrided EN214N s/steel with manganese bronze valve guides, Nominal 21.4cc with by pass hose and heater take off holes open. This specification of cylinder head, based on used core castings, is modified to current...
STAGE 1 KIT. Mini Spares bolt-on performance kit for 998 and 1098 engines.
Similar to C-STN17 except it has a large bore side exit exhaust.
Always get your car rolling roaad tested for best ignition/timing and emmissio...
Genuine mini Spares inlet manifold dyno tested and designed for our Stage one kit C-STN17. The single SU manifolds is developed to give maximum airflow and gas speed, yet fit all engines even if the standard air cleaner set-up is used. I...
same kit as C-STN18 but with the correct needle for the larger HIF6 carb 1.75"
which has a 100 thou jet tube--an alternative to the needle supplied is BDL if other slight modifications or exhaust changes heve been made
STAGE 1 KIT. Mini Spares bolt-on performance kit for 998 and 1098 engines with HS4 carb. Gives 20% more power and 12% more torque.
Using all the top quality tried and tested parts the Kit includes
RC40 twin box [link]RC...
STAGE 1 KIT. Mini Spares bolt-on performance kit for 998 and 1098 engines gives 20% more power and 12% more torque.
This money saver kit however is for further stages of tune and contains a Maniflow LCB exhaust manifold- twin box RC...
Performance Stage one kit for 1300cc models with HS4 or HIF38 Carb with side exit large bore exhaust system RC40-010
Always get your car rolling roaad tested for best ignition/timing and emmissions after fitment.
Performance Stage one kit for 1300cc models with HIF44 Carb with centre exit exhaust system RC40-12
Performance Stage one kit for 1300cc models with HIF44 Carb with side exit large bore exhaust system RC40-10
STAGE 1 KIT FOR MINI VAN, ESTATE AND PICKUP. Mini Spares bolt-on performance kit for 998 and 1098 engines. Gives 20% more power and 12% more torque.
Always get your car rolling road tested for best ignition/timing and emmissions after fitmen...
STAGE 1 KIT. Mini Spares bolt-on performance kit for 998 and 1098 engines.
Similar to C-STN17 except it has a centre exit exhaust.
Kit includes - single box RC40 Millennium large bore centre exit exhaust system,...
35.6 x 29.3mm steel valves with chrome stems and cast iron valve guides.
No by pass hose and blanked off heater outlet as per SPI heads
This specification of cylinder head is modified in true Road sport style to maximise on-road pe...
To convert a standard UK spec Single Point Injection car to HIF44 carb. This kit includes wiring looms,fuel tank,fuel pump, carb, air filter and inlet manifold.
STAGE 1 KIT FOR MINI VAN, ESTATE AND PICKUP. Mini Spares bolt-on performance kit for 1275cc engines with HIF44. Gives 20% more power and 12% more torque.
Always get your car rolling roaad tested for best ignition/timing and emmissions after ...
Spring seat shims (set of 4), 0.020" thick (0.5mm).
Spacer shims to increase valve seat pressure and overall spring rate.
These were also used on all the 8 port head valve seats to prtect the alloy seats from wear. (8 port now C-AHT...
Spring seat shims (set of 4), 0.040" thick (1mm).
Spacer shims to increase valve seat pressure and overall spring rate.
These were also used on all the 8 port head valve seats to prtect the alloy seats from wear. (8 port now C-AHT36...
Fitting kit comprising of studs, nuts, plain washers, spring washers and a gasket
This kit of head studs is the best available for road and lightly tuned engines. See the C-AHT280 set for highly tuned engines.
The material spec is alloy steel heat treated to 75 tensile tons per square foot minimum and finish...
ARP Head stud kit that compromises of;
4 x Long Head Studs
7 x Short Head Studs (Disregard 2 if you're using a 9 stud application)
11 x Multipoint ARP nuts
11 x Heavy Duty Washers
4 x Rocker post studs <...
Silicone hose kit for 998 vehicles from 1989 onwards that were equipped with the plastic inline heater valve, comes complete with moulded heater take off pipe and 5/8 heater pipe.
Original 7/16" spring type hose clip as used on later cars (approx 1990 on) for some radiator hoses and fuel lines.
Seal for between the brake servo and master cylinder, fits all late 1988 onwards vehicles where the master cylinder was mounted directly to the servo unit.
MPI only. 3 YEAR GUARANTEE-UK made.Large impeller higher capacity water pump. Mini Spares procured product as original Rover Airtex tooling has been scrapped.
Fitted with a PPS, glass filled plastic impeller as used by Jaguar and Aston Marti...
3 YEAR GUARANTEE-UK made.Large impeller higher capacity water pump with top quality die cast body . Mini Spares procured product as the original superb Rover Airtex tooling has been scrapped.
Fitted with a PPS, glass filled plastic impeller...
3 YEAR GUARANTEE-UK made. Large impeller higher capacity water pump with a high quality die cast body. A Mini Spares procured product as the original superb Rover Airtex tooling has been scrapped.
Fitted with a PPS, glass filled plastic impe...
New competition valve cotter, these are precision CNC machined from 4340 and heat treated to a better spec than EN24T and claimed to be stronger in fatigue life.
These locate better in the valves and easier to control spring heights.
Upgraded rocker cover gasket made in silicon, cut outs for 11 stud head and ideal when rocker cover is removed on a regular basis.
Rarely you may require longer rocker cover bolts when fitting this so use CAM6823.
Unlike polished covers, these red powder coated aluminum valve covers don't get that dingy look; simply wipe them and they're clean. (Fins and Mini Spares logo remain cast aluminum finish) And they're made to clear our hi-lift rockers. Available...
Upgraded rocker cover gasket made in silicon, ideal for race cars etc where the rocker cover is removed on a regular basis. Mini Spares fitted one on their 1380cc engine road car in August 2014 with great results. Rarely you may require longer rocker...
Replacement rubber grommet for the servo vacuum hose for the 1992 onwards brake servo (GSM119)
Universal aluminium heater assembly complete with heater matrix and electric fan. Comes with 2 outlets for demisting windscreen and 2 variable vents for heating the rest of the car. Ideal for track/race cars or simply for those who want to replace th...
Set of strong lightweight titanium top caps to suit our valve springs C-AEA526/527 hard for single collet competition valves. Sold as a set of 8.
Silicone heater hose, 1 Metre for cars with the inline type heater valve or a straight take off on the cylinder head as fitted to post 1984 cars.
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.