£145.00 exc vat
£174.00 inc vat
In stock
£145.00 exc vat
£174.00 inc vat
In stockRecommended usage 1 x AAM1022 to fit one mini.
genuine panel that holds the headlamp assembly on the mini clubman versions.
this is the left hand side
From Xparts - but not original Rover - 2 of these rubber mountings are fitted at the front of the front subframe on all vehicles from 1976 (mk4) on. To help quieten road and engine noise. To stabilise steering by stopping subframe movement we suggest...
genuine panel that holds the headlamp assembly on the mini clubman versions.
this is the right hand side
the vertical panel that sits between the bonnet slam panel (MS149) and the front panel on clubmans only
The only bonnet landing panel available for the clubman shape body for a long time this part is perfect in every detail and was used on the heritage bodyshells.
A Genuine panel is now available from BL Heritage CZH149.
...
genuine front panel for the mini clubman before 1976 when the subframe was rubber mounted.see AAM1022 for rubber mounted type as fitted from 1976 on.
the front of these panels is the same but the subframe mounting bracket on the...
Really a built up half front end for the mini clubman, consists of a lower panel with headlamp panels,slam panel and stiffener between the front and slam panel. 76 ON--no inner or outer wings
Floor pan for Mini van/estate with no x member for remote change gearbox. Non Genuine. For saloon see 14A6491
picture is just to show what you get but bulge on centre tunnel for starter button appears to be on wrong side as this...
L/H Inner hinge type A post repair panel with hinge fitting holes mini, MK3
this is a genuine heritage part.
R/H Inner hinge type A post repair panel with hinge fitting holes mini, MK3
this is a genuine heritage part.
This Non genuine pattern panel has the holes for windscreen wipers and jets with barely an inch of pillar.
On cars from 1992/3 on check the original windscreen drain channel as the VIN numbers were stamped above the clutch master cylinder-wi...
Really a built up half front end for the mini clubman, consists of a lower panel with headlamp panels,slam panel and stiffener between the front and slam panel. 76 ON--no inner or outer wings
Reproduction version os ASJ360070. For the twin point only as it changed shape to accommodate the front mounted radiator and different bonnet fittings.
The full inner wing with wheel arch section for the mini clubman range --if you need only the first 20" approx of the inner wing see CZH3063.
The only bonnet landing panel available for the clubman shape body for a long time this part is perfect in every detail and was used on the heritage bodyshells.
A Genuine panel is now available from BL Heritage CZH149.
...
A non genuine panel made for repairing the corner of the windscreen panel which is prone to rust from water splashing up from underneath the front wheel arch.
Experience has shown its easier to fit the genuine panel HMP441001 al...
You can spend hours cutting out rust and patching holes, but why bother? These reproduction floor pans extend the full width with vertical flanges for easy installation and fairly well represent the original stamping. They have added metal to include...
You can spend hours cutting out rust and patching holes, but why bother? These reproduction floor pans extend the full width with vertical flanges for easy installation, and fairly well represent the original stamping. They have added metal to includ...
1970 on, cars with internal hinges and wind up windows
This repair panel has holes for the hinges on A post and overlaps 3.5"(85mm)onto the wheel arch section of inner wing
1970 on, cars with internal hinges and wind up windows
This repair panel has holes for the hinges on A post and overlaps 3.5"(85mm)onto the wheel arch section
THIS PANEL PROTECTS THE UNDERSIDE OF THE WINDSCREEN VALANCE UNDER THE FRONT WING SECTION also fitted on the inner wing panel 14A8346/7
Inner l/h wing with large fan hole from 1991-96. This panel is available with the A panel fitted for ease of fitment as ABD36005
Was ABD36009 but that did not have the stiffener plate for the damper bracket fitted which was diff...
See ALA5661MS for an upgraded thicker and best fitting aftermarket L/H A panel-all the local bodyshops fit this.
Known as an A panel this is for all wind up widow type cars with internal door hinges and is single skin as opposse...
This late front panel will fit any Mini, with rubber mounted subframes, manufactured after 1976. It is probably easier to replace the entire panel than to repair a damaged one, especially if it's been hit more than once. Early Minis can use [link]MS4...
A non genuine panel made for repairing the corner of the windscreen panel which is prone to rust from water splashing up from underneath the front wheel arch.
Experience has shown its easier to fit the genuine panel HMP441001 al...
Genuine panel that has the holes for wipers and jets with only a few inches of pillar which is basically the area that rots. Also referred to as the windscreen scuttle lower panel. Fitting the genuine type ensures you should get a better windscreen a...
Fits round tunnel cars. Approximate location of the vertical, forward wall is 17.5 - 17.75 inches back from the crease in the floor where the floor bends upward under the pedals. The forward wall lines up just forward of the front portion of the exte...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.