£206.01 exc vat
£247.21 inc vat
In stock
£206.01 exc vat
£247.21 inc vat
In stockRecommended usage 1 x C-AEG362 to fit one mini.
This bracket bolts on the gearbox and attaches to the exhaust front downpipe clip GEX7053.
Manifold gasket fitted to all A series pre 1992 except Turbo which had a reinforced exhaust ports GUG704063MG and SPI from 199. From 1991 on a new better gasket with reinforced exhaust ports and backing was fitted GUG704053MG
Exhaust manifold to downpipe clamp. For 32mm o/d pipe size.
The key to eliminating exhaust leaks at the manifold flange is the clamp. These cast clamps are the best style to use. A real piece of kit to use eradicating a multitude of likely p...
This is the clamp on the cooper freeflow manifold to clamp it to the engine for extra support, supplied with tag.
Special reinforced gasket for injection cars has metal inserts on exhaust ports plus a metal back on the manifold side which makes surface easier to clean when replacing. Often used on Turbo cars when correct gasket is in short supply.
...
The intake/exhaust manifold should be secured to the head with brass nuts and these very thick washers. These washers are intended to not only spread the clamping action but the thickness allows them to absorb the heat without deforming! Takes 4 per ...
This is the clamp for the C-AEG365 manifold that clamps it to the engine for extra support.
Manifold gasket fitted to all A series pre 1992 except Turbo which had a reinforced exhaust ports GUG704063MG and SPI from 199. From 1991 on a new better gasket with reinforced exhaust ports and backing was fitted GUG704053MG
If you wish to delete the catalyst (legal restrictions apply, so check to see if you are allowed) this pipe is specially made to replace it.
1.75" bore single box, centre exit exhaust system. This exhaust system by Maniflow is straighter and louder than our RC40 system. Very high quality with a skid plate on the bottom of the silencer and a polished stainless tip. Suitable for use with an...
Standard larger 1.750" bore single box exhaust system for saloons.
see C-ARA339 for van and pickups.
1.75" bore twin box, centre exit exhaust system. This exhaust system by Maniflow is straighter and louder than the RC-40. Very high quality with a skid plate on the bottom of the muffler and a polished stainless tip.
Locating rings originally made for 12G295 heads with twin carbs to line up the inlet manifold to the inlet ports on the cylinder head it found its way on most twin carb factory produced cars. There is a recess in the inlet port on the he...
Genuine mini Spares inlet manifold dyno tested and designed for our Stage one kit C-STN17. The single SU manifolds is developed to give maximum airflow and gas speed, yet fit all engines even if the standard air cleaner set-up is used. I...
Not road legal except for turbos this is a 2" bore single box system. Side exit
and for twin box see C-ARA334
Spacer block between carb and manifold for single HS2 carb. To use on twin carbs the fixing holes need drilling out to size. 7.5mm thick
Cast alloy type,this intake manifold for twin 1.25"SUs (H2 or H4 -- NOT HS4)
It has been carefully produced to minimize cross-port-flow interference caused by the balance tube and has generous radii in all the right places. Further blending ...
The very rear bobbin type mounting rubber on every mini made until the introduction of a rubber hanger strap in 1992. When the RC40 or similar systems are fitted, 2 will be required. This is a stronger poly version.
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.