STUD FOR SCREW ON OIL FILTER PLUS HS2 CARB
CHS2613

£1.68 exc vat

£2.02 inc vat

In stockIn stock
3/8"unc 1.6250" long stud for engine block to accept the TAM2097 screw on filter head and for HS2 carbs, alternative to this is CHS2614 1.75" long and just over one thread longer. LYG10008 bolt was later alternative for the filter head

UNC course thread for manifold or block and UNF for the nuts. See also 22A152 longer stud for some HIF carbs.

£1.68 exc vat

£2.02 inc vat

In stockIn stock

Recommended usage 2 x CHS2613 to fit one mini.
Block Components & Pistons - Qty 2
Inlet & Exhaust Manifolds - Qty 2
Engine and Block 998cc - Qty 2
Engine and Block 1275cc - Qty 2
Oil Pumps, Filters and Coolers - Qty 2

Alternative products

Originally quoted as the HS2 twin carb manifold stud it is one thread longer than CHS2613 which was for single HS2 and spin on oil filter head to the block. UNC course thread for manifold or block and UNF for th...

later cars used this bolt to hold on the spin on filter head to the block-earlier cars used the CHS2613 stud--both are interchangeable

3/8"unc 1"long

Kit products

A kit to convert the early style cartridge oil filter to the later style spin on filter.

People also bought products

This is the original type of needle valve that governs the plastic fuel float in your SU carb.

An alternative better upgraded version is available as CA90.

Timing cover front plate and tensioner plate bolt and washer kit. Comes with all parts to fit the cover except for the counter sunk screws if fitting a duplex kit (our duplex kits all come with these).

Return spring kit for HS4 carburettor spindle.

Complete nut, bolt and washer set for engine to gearbox only

Water pump fitting kit for models without bypass facility, includes new bolts, washers and superseal gasket.

Complete fixing kit for a water pump, includes replacement silicone bypass hose, clips, superseal gasket, replacement bolts and washers.

later cars used this bolt to hold on the spin on filter head to the block-earlier cars used the CHS2613 stud--both are interchangeable

3/8"unc 1"long

Metal bracket that fits between the manifold and the HIF44 (1.75")carb to hold the cable - the choke cable clip for this bracket is CZK6491. Also for HIF38. For HS4 carb see 12G766 bracket. Original Turbo type [...

Universal stud made for fitting the HS4/HIF carb to the manifold (except HS6 with alloy spacer on cast one piece manifold which requires CHS2515 (5.8mm longer)) and it also fits the cylinder head to take the thermostat housi...

Originally quoted as the HS2 twin carb manifold stud it is one thread longer than CHS2613 which was for single HS2 and spin on oil filter head to the block. UNC course thread for manifold or block and UNF for th...

There are 3 of these bolts fitted -1.75"long 5/16"UNF bolt ALTERNATIVE DAM7758.

Also used as longer bolt for water pump.

Also for the 21A1091 heavy duty tie rods on front suspension.

A series mini engine crank pulley bolts have been known to come loose, caused by pulley damper vibration on competition engines. This is a high tensile longer extended thread cap head bolt with thick washer to rectify this problem and also allow furt...

Twin carb HS2 (1.25")black heatshields with link bar and 3 new return springs.

Before the days of Aeroquip, Minis were fitted with braided steel rubber fuel lines. They should be used in place of rubber for all fuel lines in the engine compartment. They come made to length, with rubber end caps. 1/4" bore size.

Orange ...

Clip on the heater valve for heater cables on vehicles from 1990 where the in line remote heater valve was used. It has also been used as a clip for HIF carbs to hold the cable but the one from Rover is 13H3472.

Longer main bolt stud.

As supplied with our main strap kit.

Before the days of Aeroquip, Minis were fitted with braided steel rubber fuel lines. They should be used in place of rubber for all fuel lines in the engine compartment. They come made to length, with rubber end caps. 1/4" bore size.

Orang...

The high tensile bolts supplied with the 998 centre main strap kit.

GASKET BETWEEN CARB AND AIR CLEANER ALLOY ELBOW