£0.67 exc vat
£0.80 inc vat
Out of stock
£0.67 exc vat
£0.80 inc vat
Out of stock
Top Radiator Hose.
Unless your're heavily into the concours scene you'll love these hoses. These silcone hoses will withstand higher temps and pressures and will last virtually forever. Made to fit any 850/998/1100cc minis plus HIF38 carb c...
2 plastic 5/8" outlets at the same end and close together which exit the heater on the r/h side. The later HIF38 1275 and single point cars had a change point where the plastic outlets exited on the l/h. This is a JEF10005.
These units take ...
Standard Mini radiator with 3 offset tubes in the core. Metric thread fixings.
Flanged metric thread bolts are available as FS106107separately.
See also, alloy radiator in same shape but 2x18mm tubes as an alternative
Original mini half inch bore heater hose cut to metre lengths as required.
The MK1/2 had one hose 35" and one at 16" long, MK3 had one 35" and one at 29".(These are all maximum lengths).
Please note MK4 1976 on some had 42" heater t...
Minispares own UK manufactured product with original shape mini header tank, now with drain plug in lower tank which doubles up to also accept the screw in type sensor for later cars. It has about 20 fins/ gills per inch with 2 tubes in the core and ...
Water hose pipe clip for the GRH1140 top hose and twin point injection cars which had larger hoses fitted .This clip will wind down to fit most radiator hoses if required.
Real Kevlar stranded hose,2 year guarantee-the only true Kevlar threaded hose available where you can see the strands, it is made for longevity and low heat transfer making this the best selling bottom hose in the market.
The built in proper...
The original highest pressure cap as used on the 1275 cooper S until they decided to fit 88 degree thermostats and 15LB rad caps on A plus units.
An ECE (vehicle safety regulation)in 1974 introduced the 15lb cap which is as high a pressure a...
Special thin type clip for fitting the water by pass hose between the water pump and the cylinder head. Most ordinary jubilee clips will not fit the tight area where the hose fits. Also used on C-AHH8537 oil cooler hose.
If you drive A-Series cars long enough you will eventually have to replace the water pump bypass hose. These are the best quality available to fit without removing the cylinder head but these fluted rubber hoses have a bad reputation so if possible ...
Probably the most changed stud on the mini. This is the length used on every A series engine until the introduction of the sandwich plate when longer ones were required. A stainless steel variety C-STR286 is available which we do recomme...
Set of engine block and filter head unions for pre 12A engines (1992).
these take push on oil cooler hose.
from air vent on dash to duct-about 5"(128.9mm)long with 2.5" diameter
Standard alloy thermostat housing. If you want the larger bore type as used on the Cooper with a sandwich plate see PEQ10019 housing GRH1140.
Requires thermostat gasket GTG101MS or GUG705558G...
Hose clip for 5/8" heater hose and used to locate 3/4" diameter anti roll bar in our C-AJJ4008 kit.
Upper radiator longer hose for small bore Mini Mk1. This fits early radiators where the outlet is at the very front edge. This outlet moved about 1-1.5" closer to the centre on current radiators as used on the MK2
Clear plastic windscreen washer tubing sold by the metre only. This is the larger size and was known as 1/4" bore because GWW201M is 1/8" bore. This hose is actually now known as 4.8mm which is nearer 3/16".
this was known as 1/...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.