(¥240) £240.00 exc vat
(¥288) £288.00 inc vat
In stock
After removing the cap you can select between 16 different curves by using
a screwdriver. A bright flashing led light shows which curve you have selected.
Each CSI dizzy comes with 16 pre programmed maps, this one suitable for all Pre A+ 850, 997, 998, 1100 and non cooper S 1275's.
See C-27H7711 NON VAC for some performance use. Use with 3ohm coil GCL216.
(¥240) £240.00 exc vat
(¥288) £288.00 inc vat
In stockRecommended usage 1 x C-27H7710 to fit one mini.
CSI-Ignition is a fully electronic ignition built in an original housing. You will have to remove the cap to see the difference! Neg earth only
After removing the cap you can select between 16 different curves by using
a screwdriver...
These are the screws needed to fix the condenser, points and base plate to 23/25D distributors. See 57H5135 for 45D type distributors.
the oil seal to fit on 12A1136 distributor housing. Pre A Plus
the earlier housing 2A612 did not have a seal.
If you have an original 25D type distributor this is an upgraded arm (blade moulded and riveted )for performance use because all the other types available now are likely to fail at high revs. Because the blade is thin,or the rivet sometimes to long a...
This distributor clamp should not be bent; if it is, either you can't get the dizzy all the way in or it won't grip.
Designed to fit the GDC102 side entry distributor cap as a protection against water, made in rubber.
for 23/25D distributor but see [link]47H5250[/link} for resin type upgrade with 3m of wire as opposed to every aftermarket type analysed with only 1.5m of wire.
its worth paying extra for the condenser and rotor arm [link]GRA101]/link]
best plug for 12g295 head as fitted to 998 cooper--for tuned head use B7ES.
this is good for any head where a lot has been machined off-flat top pistons.
Coil bracket fitted to end stud of cylinder head,clutch end for coil to mount on as fitted 1969-94-MK3 on. This has been made to the original specification with the welded lug nuts rather than the cheaper method of having just plain holes to take a b...
Best on the market, sports coil-Not Lucas. A standard coil can only do so much, and when compression is raised (as in most high performance engines) or improper fuel mixtures occur something better is needed. This sports gold coil with proven origina...
Original mini coil fitted to all cars up to 1983.
3ohms
NOT for ballast type ignition systems.
Our research, sales and feed back shows Intermotor coils to be the best available for the mini.
Original type coil bra...
Quality HT lead set for twin point injection minis. For use with M4 type coil. Spiral bound wire giving instant greater resonance.
Rotor arm for all A series electric distributors when points are not fitted, except for turbo. The distributor cap for this rotor arm is GDC156.
A higher compression engine should have a colder spark plug. The engineers explain that it has to do with flame temperature and overheating the plug. I know from experience that my race engine will melt a street plug. Choose from the following NGK pl...
This was the first mini distributor cap to have screws hold the cap to the body from about 1990 on, when electonic ignition was introduced. Therefore there is no points or condenser but the rotor arm to use is GRA2143. Fits all 1992 onwa...
This is the standard non ballast coil as used on the late Mini with factory electronic ignition for use with 65D distributor.0.9ohms.
GCL143 was the Genuine Rover part fitted part on 1275cc from 1990.
0.9ohms
GCL2...
MK1/2/EARLY MK3. 3 position spring loaded type. Comes with barrel.
For barrel only use part number 24G1345.
Slightly hotter running engine plug for A Plus 998 and all 1275cc standard engines. For engine running CR of 9.4 to 10:1
The original blue rotor arm was fited with a blue cap GDC143 to the turbos and were made stronger by moulding and riveting the contact plate to the arm, so if you are looking for an upgrade on your 45D body distributor this is our altern...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.