(¥162) £162.41 exc vat
(¥195) £194.89 inc vat
In stock
pressure which effectively upgrades the actual performance of the verto clutch, which with the AP pressure GCC679 (part of GCK151MS) exceeds all previous high clamping pressure plates except for our new C-AEG485 which is 20% upgraded.
Light steel outer section for Verto type assembly which Weighs approx 9.3lbs (4.23kg) compared to the standard 5.6kg(12.3lbs)
Effects of lightening rotating engine components:
(0.5 x n2 x r2 + R2) / R2
n = total gear ratio (gear ratio x diff ratio)
r = radius of gyration
R = Radius of wheel/tyre
This formula gives what accelerative weight the engine sees of the car per lb.
Radius of gyration of a transverse engine's flywheel is approx. 3.75"
So to determine "weight loss" for a flywheel weight of say 18 lb to 10 lb,
the engine would see an overall weight loss of the car to accelerate in first gear of:
3.33 = 1st gear of 4 synchro 'S' box
3.44 = diff ratio
(0.5 x (3.33 x 3.34)2 x 3.752 + 9.52) / 9.52
= (0.5 x 131.2 x 14.06 + 90.25) / 90.25
= 1012.59 / 90.25 = 11.22 lbs
So for every 1 lb removed from the flywheel, the engine sees 11.22 lbs less
to accelerate off of the total car.
Therefore by lightening the flywheel by 8 lb,
the engine sees a total reduction of the cars accelerative weight of 89.68 lb.
On the flywheel, check the pedestals which the pressure plate bolts onto in case it has sharp edges, which can interfere with the springs on the pressure plate
preventing it from moving (clamping it).
This flywheel is designed to be fitted with a Valeo pressure plate. If an AP type pressure plate is to used, it may be necessary to relieve the two holes on the pressure plate used for the location onto the flywheel. Standard Clutch and flywheel kits available are as follows:
GCU90115AF uses C-AEG422 flywheel/GCK151MS 180mm plate kit - 998/Some Metro 1275
GCU90116AF uses C-AEG422 flywheel/GCK371AF 180mm plate kit - Turbo
GCU90121AF uses C-AEG425 flywheel/GCK152MS 190mm plate kit - Singlepoint Inj GCU90122AF uses C-AEG422 flywheel/GCK152MS 190mm plate kit - Carb type 1275 90-94
GCU90123AF uses C-AEG424 flywheel/GCK152MS 190mm plate kit - Multipoint Injection
(¥162) £162.41 exc vat
(¥195) £194.89 inc vat
In stockRecommended usage 1 x C-AEG422 to fit one mini.
A steel flywheel with a complete AP pressure and clutch plate and release bearing, all sold as separate pieces in kit form - has 180mm clutch plate for pre 1990 cars which includes 998cc and some Metro 1275cc. If the flywheel centre boss is required ...
Verto clutch assembly for all Non Injection cars, supplied unbuilt in separate parts less the centre boss. Fits pre injection cars that all had a pre engaged starter. This has a 190mm plate and a lightened steel flywheel C-AEG422 which p...
Turbo Verto clutch assembly sold as separate parts - includes steel flywheel, Turbo pressure plate and release bearing; if the flywheel centre boss is required see DAM5921. Original flywheel no longer available
GCU90115...
Ring gear for all cars fitted with the pre-engaged starter on Verto flywheels from about 1984 on.
Non Genuine three piece verto clutch kit, has a 180mm wide clutch plate, pressure plate and release bearing,fits all cars pre 1990 VERTO assemblies until fitment of 1275cc engines. For Borg and Beck see GCK151MS
From 1990 on the...
Non Genuine 3 piece Injection Clutch with the larger 190mm wide for 1990 on and all injection cars, but it can be used on earlier non injection Verto type engines only if the flywheel is 100% PERFECT WITHOUT WEAR. Check nothing fouls when bolting up ...
Upgraded Centre boss for all verto clutch/flywheel.
Fixing bolts are DAM5920 which are supplied in many clutch kits.
This is for single point injection cars. should be balanced with pressure plate.
This flywheel must use a VALEO PRESSURE COVER or Minispares C-AEG485 with 20% upgraded pressure or the car WILL NOT START because the timing slot w...
Race quality shoulder bolts for the Mini clutch backplate to the diaphragm--sold seperately- heavy duty racing type EN16 tightenn up to 16lbs per sq foot torque when using shake proof washer or 18lbs and locktite. Use with C-2A3659 race ...
Clutch housing bolt to engine long 5/16" UNF 1.75" long with tuflock patch to secure. Earlier bolts less tuflock are {link]BH605141{/link}
3 piece Verto Clutch kit for Turbo with 180mm plate which can be used on any Verto flywheel including injected cars. Approximately 20% upgrade over standard this is ideal for any tuning mods to any Verto flywheel but cars from 1990 were fitted with a...
Performance type Verto 190mm wide paddle type drive plate as used for racing.
This will not fit pre Verto backplate/flywheel as it is to wide.
Performance type Verto 180mm wide paddle type drive plate as used for racing.
Alternative to AP Racing plate
Mini Spares Performance clutch plate.
Great upgrade for increased performance engines,tested to 10,000rpm and to destruction for evaluation.
For diaphragm type clutch, pre verto. Great clutch plate and a better priced alternative t...
Performance clutch plate for road and rally Verto type - see also 20% upgraded pressure plate
This Verto type clutch arm is 2.75" long from the clevis pin hole.The earlier type pre verto is over 6"(165mm)long. the ball wears on both types and if the clutch is wrongly adjusted the arm (mainly the long type) can bend by way of hydraulic pressur...
Delete the metal pipe and existing hose by fitting this longer one piece steel braided pipe which can be used for either early or verto clutches. A sensible modification for all mini owners.
FOR ALL 1300cc verto clutches which are 190mm wide
When the verto clutch was introduced the factory started fitting this plastic protector over the clutch oil seal on Metro's. It then apeared on injection minis with LUF10005 clutch seal to the end of production. Should be replaced when s...
3 piece Borg and Beck Injection Clutch with the larger 190mm wide for 1990 on and all injection cars, but it can be used on earlier non injection Verto type engines only if the flywheel is 100% PERFECT WITHOUT WEAR. Check nothing fouls when bolting u...
Steel braided clutch hose for verto type clutches with short lever arm.
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.