(¥264) £263.99 exc vat
(¥317) £316.79 inc vat
In stock
These extra high-spec alloy Purple rockers were introduced in 1998 to give push rods a better clearance on A Plus heads.
Pre 1998 blue type pre are not interchangeable.
Our material spec is higher and therefore more expensive than many others available on the market.
The alloy rockers have hard centreless ground roller tips and PB1 phosphor bronze material bushes on a competition thick-wall Mini shaft,with nuts and EN8 adjuster screws.
Ensure you tighten down all posts equally to eliminate stress fractures on shaft if used on small bore heads (not advised)it is necessary to re-arrange the rockers to line up the tips with valve stems.
The ultimate lightweight alloy valve gear giving maximum efficiency cutting down side loading on valve stem, reducing friction and wear whilst increasing rigidity. The 1.5 hi-lift keeps valves open approximately 20% more at any given point, although opening and closing periods remain the same, and vastly improves volumetric efficiency and, therefore, power output.
These combine in a high quality yet economical roller rocker set, as the roller tip is the most important factor to reduce valve and guide wear when using modern performance cams.
We advise using spacer kit C-AEG392
Ensure that the rocker cover has clearance for these rockers FP24 rocker cover or Mini Spares own covers will give clearance on high lift rockers.
The CAM6822 rocker cover we sell has also been fitted but check clearance and may need slight fettling or carefull alignment.
(¥264) £263.99 exc vat
(¥317) £316.79 inc vat
In stockRecommended usage 1 x C-AHT446A to fit one mini.
Goes on both ends of the rocker shaft to keep tension on the #1 & #8 rockers.
original rocker shaft spring (3) between rockers on every A series engine
Mini Spares spacer kit re-designed in 2005 for correcting rocker alignment.
This kit has been produced to help rocker pad and valve stem alignment plus reducing friction. The standard springs can be replaced with this special kit of 3 spacer...
Hi-Lift forged rockers on our special rocker shaft with AEG167 adjuster screws for road or race.
Ensure posts are equally tightened down to eliminate stress fractures on shaft.
Using 1.5 ratio high lift rockers has alm...
Roller-tip rocker assembly. 1.5 Hi-Lift for 1275cc big bore engines only.
Craddle type with larger upgraded shaft size to improve rigidity.
Ensure tightening down all posts equally to eliminate stress fractures on shaft.
This kit uses the race quality valves and alloy roller tipped rockers but for a cheaper version but identical in power see C-STN21BUDGET. Both kits give more or
less the same gains which is a true 20-25%
For cars with HIF44 (1.75")carbs this kit includes a modified large inlet valve gas flowed head -1.5 rockers, gaskets, plugs, K&N air filter element, and a twin rear box silencer.
20% - 22% power increase plus better pulling power and smoother. Also noticable gains at the top end and runs perfect with existing ECU. Keith Dodd has now done 11,000 trouble free miles in his car. Exhaust is finished in Mild Steel.
Genuine Mini Spares upgraded UK made EN8 screws, specially heat treated in correct places as per original drawings, sold individually without nuts.
Nuts are sold individually as NT605061.
Used on our 1.5 forged and roll...
Direct replacement rocker shaft. Fits all except full needle roller types. Far superior to the stock item! ENSURE YOU ALWAYS TIGHTEN DOWN ALL POSTS EQUALLY to eliminate stress fractures on shaft.
Our special "heavy duty" shaft has ...
Hi-Lift forged rockers on our special rocker shaft with AEG167 adjuster screws for road or race.
Ensure posts are equally tightened down to eliminate stress fractures on shaft.
Using 1.5 ratio high lift rockers has alm...
Victor Reinz large bore head gasket for A-series engines.
Spring seat shims (set of 4), 0.020" thick (0.5mm).
Spacer shims to increase valve seat pressure and overall spring rate.
These were also used on all the 8 port head valve seats to prtect the alloy seats from wear. (8 port now C-AHT...
Fitting kit comprising of studs, nuts, plain washers, spring washers and a gasket
This kit of head studs is the best available for road and lightly tuned engines. See the C-AHT280 set for highly tuned engines.
The material spec is alloy steel heat treated to 75 tensile tons per square foot minimum and finish...
ARP Head stud kit that compromises of;
4 x Long Head Studs
7 x Short Head Studs (Disregard 2 if you're using a 9 stud application)
11 x Multipoint ARP nuts
11 x Heavy Duty Washers
4 x Rocker post studs <...
New competition valve cotter, these are precision CNC machined from 4340 and heat treated to a better spec than EN24T and claimed to be stronger in fatigue life.
These locate better in the valves and easier to control spring heights.
Upgraded rocker cover gasket made in silicon, cut outs for 11 stud head and ideal when rocker cover is removed on a regular basis.
Rarely you may require longer rocker cover bolts when fitting this so use CAM6823.
Unlike polished covers, these powder coated aluminum valve covers don't get that dingy look; simply wipe them and they're clean. (Fins and Mini Spares logo remain cast aluminum finish) And they're made to clear our hi-lift rockers. Available in ...
Unlike polished covers, these red powder coated aluminum valve covers don't get that dingy look; simply wipe them and they're clean. (Fins and Mini Spares logo remain cast aluminum finish) And they're made to clear our hi-lift rockers. Available...
Upgraded rocker cover gasket made in silicon, ideal for race cars etc where the rocker cover is removed on a regular basis. Mini Spares fitted one on their 1380cc engine road car in August 2014 with great results. Rarely you may require longer rocker...
30.5mm(1.2") longer exhaust valve for the 2012 on 8 port head only
for use with special guides these are plasma heat treated to eradicate premature wear from unleaded petrol--For earlier heads see C-AHT376/7 valves.
The valve size h...
Set of strong lightweight titanium top caps to suit our valve springs C-AEA526/527 hard for single collet competition valves. Sold as a set of 8.
EN24 Nickel Chrome moly steel studs,Competition head stud kit.
torque to 45ftlbs -no need to re-torque cometic type head gaskets.
For use on the 2012 onwards heads only.
Alloy CNC version of the cylinder head take off 12G2534. The standard item being steel can be prone to corrosion, this CNC alloy version is smart, and will not corrode like steel does
35.6mm(1.4") longer exhaust valve for the 2012 on 8 port head only
for use with special guides these are plasma heat treated to eradicate premature wear from unleaded petrol--For earlier heads see C-AHT376/7 valves.
Valves now longe...
37mm(1.457") longer inlet valve for the 2012 on 8 port head only
for use with special guides these are plasma heat treated to eradicate premature wear from unleaded petrol
3.933" 99.898mm long
Large 35mm inlets-Suit any 1275cc-
Using a New MPI 1275cc head casting, built up with new valves and springs etc; all set up for unleaded fuel. Last of these brand new head castings which have slightly soiled paint etc through age.
...
3 layer steel head gasket especially suitable for full race engines up to 73.5mm
bore where it has larger bore holes and considered the ultimate head gasket.
Especially recommended for 8 port heads as it has no fire/compression ring...
Complete stud, nut and washer kit for the cylinder head ancillaries. Kit contains parts to retain the following:
Inlet/Exhaust manifold to head, studs/nuts/washers
Thermostat housing (no sandwich plate) studs/nuts/washers
H...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.