(¥15) £15.00 exc vat
(¥18) £18.00 inc vat
In stock
(¥15) £15.00 exc vat
(¥18) £18.00 inc vat
In stockRecommended usage 1 x DIZZYPLUG01 to fit one mini.
Lightweight billet aluminium distributor hole blanking plug for A+ engines.
RESIN BASED CONDENSER as per the original Lucas type made for the 23/25D type distributor as fitted to original Cooper S or Racers who want a trusty part or where originality is required,with soldered wire connections and correctly made foot to sit ...
Fited to Lucas type distributors with 45D body in 1974 until 1990 when electronic type that was held on by 2 screws appeared as oppossed to this clip on this type. If you need a new distributor clip-we have them as GDC136CLIP.
You should replace the camshaft bearings every time the block goes to the machine shop. These bearings fit all late model 1275cc blocks (the ones without tappet covers on the back) It's almost too simple and thus often overlooked during a rebuild. Ca...
Mini Spares best quality complete gasket and seal kit for engine block and gearbox,for all common engine types and sizes.
Also comes complete with Mini Spares Evolution clutch oil seal 13H2934MS, differential oil seals...
original Lucas type RESIN BASED CONDENSER made for the 45/59D type distributor if you want a quality item rather than the cheaper inferior parts available. Filled with 3m of winding inside as per original Lucas but every copy analysed to date has ...
Solid state ignition coil. M4 type for twin point injection minis.
Plugs on the current MPI coils are very snug but do fit.
Proper timing of the camshaft is very important and while it is easy and nice to do it with a precise adjustable cam sprocket it is also cheap to do it with offset cam keys. 1 or 2 degrees difference in cam timing can make a difference in performance...
Nitrided, forged 86mm stroke, 1.625" "S" big end journal for non-S 1275/1300 block with stronger keyway for timing gears fitted.
Forged EN40B steel nitrided Race cranks are considered the ultimate in specification, even over the "billet" typ...
The original blue rotor arm was fited with a blue cap GDC143 to the turbos and were made stronger by moulding and riveting the contact plate to the arm, so if you are looking for an upgrade on your 45D body distributor this is our altern...
Cup type core plug for all cooper S only @ 41.4mm wide.
4 required per engine.
Convex type core plug at 41.4mm for all early A series blocks up to A plus.
4 required per engine-these are known as the flat type wher the centre has to be pressed in so the convex plug spreads out. The Cooper S althouh same size was a cup ...
Cup type core plug for all A plus and 1275cc engines except for Cooper S. 33.6mm wide.A plus 5 required but only 4 on 998 A plus. 1275 has 2 core plugs oil pump end of block whereas 998 only has one
3 Bolt hole fixing pump for A plus 998cc engines. This has a spade type drive spindle to fit the slot in the camshafts. This replaced earlier peg type drive which fitted into camshafts with a pin (known as pin drive).
Brass type core plug for engine. Originally, engines had brass oilway plugs (2K1345) 1/4" hole fitted. These cup type plugs replaced them about 1985. 12.7mm cup type plug about 9.6mm deep. Fits 1/2" hole.
All good engine tuners ...
Plastic Y piece for joining the crankcase breather pipes on Cooper S or any twin carb cars with this ventilation system.
The ultimate cam follower with oil hole, designed to minimise float and jump normally seen in original cam followers, which ultimately loses power. Precision ground outside diameter with smaller chamfered base to give more surface area for extra hi l...
Interior lamp with a black on/off switch and pointed torpedo ends.
Also fitted many of the 1959on range of Austin A55/60 Cambridge, MG Magnette etc.
Also there was an alternative lamp with black switch and square ends 13H192 which w...
Victor Reinz/Mahle small bore head gasket for A-series engines.
Gasket fitment. Writing side up.
New competition valve cotter for early heads with the large single groove valve, these are precision CNC machined from 4340 and heat treated to a better spec than EN24T and claimed to be stronger in fatigue life.
These locate better in the v...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.