SPEEDO CABLE L/H/D 29" LONG 1988 on
GSD488

(¥14) £14.25 exc vat

(¥17) £17.10 inc vat

In stockIn stock
29" long for L/H/D cars from about 1988 on when Seiko nippon speedo gauges are fitted. earlier cars used a 33" cable GSD102 which had the grey end but are interchangable and cheaper.

(¥14) £14.25 exc vat

(¥17) £17.10 inc vat

In stockIn stock

Recommended usage 1 x GSD488 to fit one mini.
Speedo cable and fittings, clock and gauges - Qty 1

Alternative products

These have push-on connectors at the speedometer. Fits R/H/D Clubman and late L/H/D Minis to 1988 with the gauges in front of the driver. Longer versions are GSD487 at 42.5" and GSD415 at 48" long, this is also used on LHD w...

People also bought products

Sealing washer for the oil gauge to oil pipe as sold in OL kit and for 21A804 metal pipe to oil gauge.

With this large diameter line to the oil pressure guage you can actually see minor fluctuations in the pressure at idle or when the relief valve bounces open and closed. Because the braided steel line is one piece from the block to the gauge there is...

Angled oil pipe adaptor for fitting in confined spaces to eradicate damage of oil pipe, requires an OA adaptor if being used with a oil pressure gauge/t-piece.

Oil pipe in plastic 5 feet long, if fitting to a Tim gauge you will require LMA017 adaptor for the gauge.

Not comppatable with the CAM6431 standard oli pressure block union, and OA shoudl be purchased to fit.

Oil gauge adaptor for fitting into engine block or T piece.

A must if you want to run a mechanical oil gauge and retain the oil warning switch. Screws straight into the block on all A series engines.

Male to female brass spacer/adapter for mechanical water temp guage screws into head & accepts capillary tube. Required for SIB422 and SIB422MG. Also fits in MOCOT1

Speedometer cable, 30" long for Smiths type central speedo-original was 26" long

Mini Moke Speedo Cable for the Centre clock type speedo,also 13" longer to allow the Smiths type central speedo to be moved.

If you have an early Mini saloon or Estate/Van or Pickup with the fuel tank sending unit held in by screws, this is the correct screw for you.

Do not forget the special copper washers also 2A2088 and the cork gasket [link]2H10...

You will need this union for your Tim gauge if you fit a replacement plastic oil pipe part number OL

Longest cable we keep for fitting a Smiths central type speedo when engine in rear of kit car. This is the correct cable for a Sprite or Midget, not a universal cable. Includes inner cable and outer sheath.

Extra long cable for Smiths central located speedo when position moved in dash and also used as a Tacho cable for Sprite, 36" long.

48" extra long speedo cable for special fitmentswhen using original type Smiths central mounted speedo.

2.2 WATTS and fits back of gauges in cars with 3 extra 52mm round clocks.

Speedo cable for most Innocenti made minis which had Veglia speedo clocks.

26"

This is the wiring short conversion loom that fits to the old central speedo and is used by people modifying from 2 or 3 clock dashes to single clock or just repairing damaged looms. With the correct bulb holders and spade fittings. Now uses 5x [link...

This is the original type of metal pipe that fitted from the engine to the

hose on cars with central speedo and gauges. The pipe that went from the rubber hose to the gauge was 21A804. The hose is FAM2807.

...

These have push-on connectors at the speedometer. Fits R/H/D Clubman and late L/H/D Minis to 1988 with the gauges in front of the driver. Longer versions are GSD487 at 42.5" and GSD415 at 48" long, this is also used on LHD w...

Standard replacement cable for central located Smiths Mini speedometer.