(¥39) £39.17 exc vat
(¥47) £47.00 inc vat
In stock
(¥39) £39.17 exc vat
(¥47) £47.00 inc vat
In stockRecommended usage 1 x SR-037 to fit one mini.
Mini Spares best quality complete gasket and seal kit for engine block and gearbox,for all common engine types and sizes.
Also comes complete with Mini Spares Evolution clutch oil seal 13H2934MS, differential oil seals...
You should replace the camshaft bearings every time the block goes to the machine shop. These bearings fit all 1275cc blocks plus 970 and 1071 Cooper S. It's almost too simple and thus often overlooked during a rebuild. Camshaft bearings are pressed...
Genuine Mini Spares camshaft for use with 1.5 rockers if preferred--below 5000rpm should produce more power than the 286 profile. Close to MDM274
Cam Timing
107 degrees at full lift on No1 inlet
SEAT...
Price per rod-1275cc larger 6.35mm diameter push rod. Sold per single rod and 8 required per engine.
The larger diameter improves push rod rigidity as much as possible
without having to modify the block/head push rod ports. Thi...
The last Rover update on the upper engine stabiliser bar, but this is upgraded for performance use.
A one piece silent block type bush, it was fitted at both ends from 1996 on and will fit any cars that had 2 bushes fitted at either end as o...
Genuine Mini Spares valve stem oil seal manufactured with original Dupont Viton, as fitted to the twin points engines, are the best material and seal you can use and although expensive are the best to date in stopping the engine smoking.
Man...
Payen,stamped BK450, original standard composite reinforced gasket used on all large bore engines by Rover including Metro and MG Turbo and is an exceptionally good gasket.
Asbestos free with copper type sealing rings. Compressed volume is ...
Favoured by proffessionals for press fitting pistons, pre lubing bushes, roller and plain bearings, journals and gears. Prevents scuffing, seizure, wear, rust. Waterproof and corrosion proof.
A vital aid for accurately timinig non-factory camshafts. This disc is a 360 degree protractor disc made by kent cams.
Made of thicker, more pliant material with larger ports than the original gaskets. A must for use on ported heads.
Forget all the universal shape gaskets available - this is the original correct shape made out of thick gasket paper.
If you are replacing your timing chain or just doing routine maintenance a new locktab is sure to come in handy.
Hi-Lift forged rockers on our special rocker shaft with AEG167 adjuster screws for road or race.
Ensure posts are equally tightened down to eliminate stress fractures on shaft.
Using 1.5 ratio high lift rockers has alm...
If you have a mechanical fuel pump fitted to your engine this spacer block fits between it and the engine. The gaskets are available seperately however as GUG705779GM.
This is our racers favourite way of dealing with the worn or troublesome front primary gear bush.(this is NOT the top hat type rear bush)22.5mm wide. Racers and professional engine builders will use their own tolerances but these are set for road use...
Turbo oil pump, highest flow available. 9 Gallons per minute as against approx 6 GPM. This pump is a late model slot drive and will fit into any 1275cc engine and exactly the same as the second generation of pump as sold by Unipart/Rover.
Ga...
Hardened unleaded valve seats for 1.15" 1275 exhaust valves.
Require a recess of 1.2495"(31.737mm) diameter, plus or minus 0.0005" (0.013mm), and 0.250"(6.35m) deep at ambient temperature of 20C.
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.