Label | Part No | Description | Quantity | Comments | |
---|---|---|---|---|---|
1 | GWW918 | Washer bottle round with 2” (51mm) cap - Tudor type | 1 | MK1/2 Mini and MG range | |
1 | 17H2536 | Washer bottle round with 13/8” (35mm) cap - Winguard type | 1 | Original fitting MK1/2 | |
2 | 37H9712ORIGINAL | Bracket for bottle MK1/2 | 1 | Original fitting MK1/2 | |
3 | 37H9672 | Wire clip for bottle | 2 | Original fitting MK1 | |
4 | 24A1387 | Clip for bottle (bicycle type) | 1 | Original fitting MK2 | |
5 | GFK1123 | Spring washer | 2 | ||
6 | GFK3210 | Nut 3/16”UNF | 2 | ||
7 | SE910201 | Screw 3/16”UNF 3/4”long | 2 | ||
8 | 37H9712 | Bracket stainless steel for round bottle No.1 | 1 | MK1/2 Mini and MG range | |
9 | GWW916 | Small 1/2 litre washer bottle, takes small cap [LINK]GWW951[/LINK] - C.W.E | 1 | 1970-80 - use [LINK]GWW906[/LINK] | |
10 | GWW906 | Large 1 litre washer bottle, takes [LINK]GWW951/[LINK] cap | 1 | 1970-80 | |
11 | GWW907 | 1.7 litre washer bottle, takes [LINK]GWW952[/LINK] cap and [LINK]GWW951[/LINK] insert | 1 | 1980 on | |
12 | GWW935 | Bottle and cap for integral electric pump 1982-88 | 1 | Uses [LINK]GWW1192[/LINK] pump | |
13 | CZH1624 | Bracket for windscreen bottle - N.L.A | 1 | Use [LINK]CZG1496[/LINK] | |
13 | CZG1496 | Bracket for windscreen bottle in boot 1991 on | 1 | Replaces [LINK]CZH1624[/LINK] | |
14 | GWW951 | Cap for [LINK]GWW916[/LINK]/[LINK]GWW906[/LINK] (fits in[LINK] GWW952[/LINK], cap for [LINK]GWW907[/LINK]) | 1 | ||
15 | GWW952 | Cap for [LINK]GWW907[/LINK] ([LINK]GWW951[/LINK] fits into centre hole) | 1 | ||
16 | GWW102 | Manual washer pump to 1980 | 1 | ||
17 | GWW125 | Electric washer pump | 1 | 1980 on | |
18 | GWW1192 | Electric integral washer pump, fits to [LINK]GWW935[/LINK] bottle | 1 | 1982-88 was GWW130 | |
19 | GWW807 | Jet, MK1/2, black | 2 | ||
19 | MS389 | Jet, MK1/2, twin jet nut fit | 2 | Relieve bodywork | |
20 | GWW810 | Jet, Chrome, nut fit single jet MK1/2 - 1/8”bore | 2 | 3.2mm ends | |
20 | GWW801 | Jet, Chrome, nut fit twin jet - 3/16”bore 4.8mm | 2 | Relieve bodywork hole | |
21 | GWW804 | Jet, MK3 fits round locating hole | 2 | 1970-80 | |
21 | GWW1080 | Jet, fits D shaped locating hole - was GWW842 / GWW829 | 2 | 1981 on | |
22 | GWW504 | Valve for use with [LINK]GWW807[/LINK] jet - MK1/2 - Winguard type | 1 | ||
23 | GWW506 | Valve for use with [LINK]GWW804[LINK] jet - Tudor type | 1 | 1970 on until [LINK]GWW935[/LINK] bottle | |
24 | GWW401 | T piece, (3/16”) 4.8mm ends for washer hose | 1 | Uses 4.8mm hose | |
24 | GWW404 | T piece, 2 small bore ends one large | 1 | 2 x 3.2mm end & 1 x 4.8mm end | |
25 | GWW408 | T piece valve, was [LINK]GWW407[/LINK] - MK1/2/3 | 1 | 2 x 3.2mm end & 1 x 4.8mm end | |
26 | GWW201M | Washer tubing 1/8” (3.2mm), small bore (per metre) | 1 | As required | |
26 | GWW202M | Washer tubing 3/16”(4.8mm), large bore (per metre) | 1 | As required | |
27 | BAU2043A | Grommet for pump mount in washer bottle | 1 | ||
28 | GWW975 | Blue cap for [LINK]GWW935[/LINK] Bottle | 1 | Supplied with new [LINK]GWW935[/LINK] |
Note: Windscreen washer tubing was known as 1/4" bore. Now the metric equivalent is 3/16" 4.8mm bore, but known as 5mm.
This is the largest size used and fits correctly.
Reconditioned | Road/Rally | Race Quality Valves | |
---|---|---|---|
998cc | GCG1007MS | C-AHT88 | |
1275cc pre 1992 | GCG1009MS | C-AHT135 | MSE3 / MSE8 |
1275 cc 1992 on | GCG1009METRO | MSE6 | MSE4 |
MPI (Twin Point) | GCG1009 | C-AHT136 | MSE7 |