($14.98) £14.98 exc vat
($17.98) £17.98 inc vat
Out of stock
($14.98) £14.98 exc vat
($17.98) £17.98 inc vat
Out of stock
countersunk head 5/16"unc screw for holding alloy bracket 12G1318 to gearbox
2.75"shaft length
Water pump fitting kit for models without bypass facility, includes new bolts, washers and superseal gasket.
This thermostat housing fitting kit, suitable for all single tier thermostat housings. Comes with new studs, nuts, washers and Klinger thermostat housing gasket
Single blade. This is our copy of the original special tuning fan blade that we have been selling for nearly 20 years. Many people use 2 of these blades crossed over to make it a four blade fan which does makes it slightly quieter. Sold as single bla...
SEE C-GRH001 also
THE top hose is 7" long for the clubman 998/1100 and also fits the original MK1
radiator where the outlet tube on the radiator was on the very end. All new radiators have this outlet now 1.5" moved in ...
Standard Mini radiator with 3 offset tubes in the core. Metric thread fixings.
Flanged metric thread bolts are available as FS106107separately.
See also, alloy radiator in same shape but 2x18mm tubes as an alternative
Minispares own UK manufactured product with original shape mini header tank, now with drain plug in lower tank which doubles up to also accept the screw in type sensor for later cars. It has about 20 fins/ gills per inch with 2 tubes in the core and ...
Special thin type clip for fitting the water by pass hose between the water pump and the cylinder head. Most ordinary jubilee clips will not fit the tight area where the hose fits. Also used on C-AHH8537 oil cooler hose.
Known as"4-Core" Radiator, because it has 4 offset tubes in the core it is the only real "4-core" radiator available today manufactured in the UK since 1978 for MiniSpares with original top header tank shape. Our design has been proven to be the best...
If you drive A-Series cars long enough you will eventually have to replace the water pump bypass hose. These are the best quality available to fit without removing the cylinder head but these fluted rubber hoses have a bad reputation so if possible ...
Removal of the thermostat helps to reduce engine temperature, however a thermostat blanking sleeve should be fitted to maintain correct coolant circulation to the entire head. Failure to do so will cause overheating around #3 and 4 combustion chamber...
There are two of these bolts on hydrolastic front subframe towers to fix in place to the bulkhead. Fit dry suspension pre 1976 see 21A90. This bolt also holds the lower radiator bracket to the alloy casting on the gearbox when a 2 piece ...
Clear plastic windscreen washer tubing sold by the metre only. This is the larger size and was known as 1/4" bore because GWW201M is 1/8" bore. This hose is actually now known as 4.8mm which is nearer 3/16".
this was known as 1/...
In 1974 the mini changed from a two piece to a one piece cowling. These bolts ONLY fit the two piece pre 1974 cowling.
Thermostat 82 degrees. Fitted between 1981 and 1988.
Unless you're heavily into the concours scene you'll love these hoses. These silicone hoses will withstand higher temps and pressures and will last virtually forever and if you ever had to replace a lower hose you'll appreciate that last fact. These ...
Thermal transmitter fitted in the cylinder head from 1970 on until its demise on the 1990 Coopers this part was the same as GTR143. One number was original fitment and the other supplied as the spare part by Unipart.
Fits 998 1275 and cooper...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.