BAULK RING NON GENUINE

Budget priced baulk (synchro) ring has been the same since 1962, originally steel but then sintered. These rings slow down the gears to insure that they mesh without crashing. They have a machine surface on them that is the first thing to engage the ...

($6.00) £6.00 exc vat

($7.20) £7.20 inc vat

BAULK RING GENUINE ROVER USE 22G2033EVO

22G2033

Genunine Rover sintered baulk ring. Use our 22G2033EVO sintered baulk ring, which is the best quality standard baulk ring currently in the market place and as used in our 5 speed gearboxes.

Our 22G2033MS are also si...

($18.48) £18.48 exc vat

($22.18) £22.18 inc vat

COMPETITION STEEL BAULK RING

C-22A1741

Mini Spares Performance Baulk ring.

The standard sintered baulk (synchro) rings are not tough enough for the demands of performance useage, in many instances lasting only one race before failure or breakage. The main reason is the incompat...

($35.36) £35.36 exc vat

($42.43) £42.43 inc vat

GEARSET SPRITE 3 SYNCHROMESH STRAIGHT CUT (4 GEARS...

C-AJJ3319

Straight cut gear set as designed by Special Tuning which contains only the -laygear,1st Motion shaft,2nd and 3rd gears. Not only does the straight cut design provide more strength and take significantly less power to drive but the ratios of the var...

($421.25) £421.25 exc vat

($505.50) £505.50 inc vat

LAYGEAR 3 SYNCHRO STRAIGHT CUT MINI AND SPRITE

C-22G1047

Straight cut laygear for SC/CR 3-sync gearbox.teeth count 13-17-20-23

($125.84) £125.84 exc vat

($151.01) £151.01 inc vat

STRAIGHT CUT 2nd GEAR MG & SPRITE ONLY 28 TEETH

C-22G1049SPRITE

Made especially for the Spridgets to overcome junmping out of gear where hubs or selectors are worn, this is the same original ST ratio but with slightly different dog teeth design. Same for 2nd and 3rd.

($64.50) £64.50 exc vat

($77.40) £77.40 inc vat

GEARSET SPRITE 3 SYNCHROMESH STRAIGHT CUT (4 GEARS...

C-AJJ3319

Straight cut gear set as designed by Special Tuning which contains only the -laygear,1st Motion shaft,2nd and 3rd gears. Not only does the straight cut design provide more strength and take significantly less power to drive but the ratios of the var...

($421.25) £421.25 exc vat

($505.50) £505.50 inc vat

STRAIGHT CUT 1st MOTION SHAFT - SPRITE & MG ONLY

C-AEG3138

If you are using a straight cut close ratio gearbox this could be a great spare to keep. The biggest problem with this box is typically not even seen: the bearing surface for the pilot bearing that fits into this 1st motion shaft can lose its hardnes...

($192.40) £192.40 exc vat

($230.88) £230.88 inc vat

ANTI RATTLE BRASS PLUNGER FOR REMOTE GEARBOX

22A84

If your gearshift lever transmits a lot of rattle and noise, replacing these three tiny but significant parts will likely cure it. The kit for the Spridget or Minor consists of the brass plunger (22A84) and spring (AEG3123) plus the nylo...

($2.05) £2.05 exc vat

($2.46) £2.46 inc vat

PRE A+ 1ST MOTION NEEDLE ROLLER.

CHM172

This little roller bearing goes inside the end of the 1st motion shaft on minis with 14mm mainshaft which it sits on.

This bearing was previously part number 88G409 and a true Rover replacement, but if you have earlier A type gears with the...

($3.75) £3.75 exc vat

($4.50) £4.50 inc vat

COMPETITION STEEL BAULK RING

C-22A1741

Mini Spares Performance Baulk ring.

The standard sintered baulk (synchro) rings are not tough enough for the demands of performance useage, in many instances lasting only one race before failure or breakage. The main reason is the incompat...

($35.36) £35.36 exc vat

($42.43) £42.43 inc vat

LAYSHAFT NEEDLE ROLLER (ALL PRE A+)

88G396

When in doubt replace it. You have heard this many times but you better believe it on this part. If you have not personally just replaced these layshaft bearing then do it now while you have the chance. These bearing will destroy the inside of a very...

($3.27) £3.27 exc vat

($3.92) £3.92 inc vat

GEARBOX ROD CHANGE ANTI OIL LEAK SEAL KIT

MSSK050

This kit consists of one alloy sleeve with a groove on the outside to locate the O ring, the new "O" ring, a rod seal and a gaiter. To fit the kit simply remove the old gaiter if fitted and then the old oil seal. Fit the sleeve with the "O" ring fitt...

($4.75) £4.75 exc vat

($5.70) £5.70 inc vat

OUTER TRACK 1st GEAR/2nd SYNCHRO 22G1119 SPRITE

22G1118

32 tooth first gear outer track only, for the sprite/midget 3 synchro gearbox.

This part number was for complete 1st gear hub assembly originally and the outer track was 22G1119 but when Rover stopped production we used this same number for<...

($112.50) £112.50 exc vat

($135.00) £135.00 inc vat