£64.50 exc vat
£77.40 inc vat
In stock
£64.50 exc vat
£77.40 inc vat
In stockRecommended usage 1 x C-22G1049SPRITE to fit one mini.
Budget priced baulk (synchro) ring has been the same since 1962, originally steel but then sintered. These rings slow down the gears to insure that they mesh without crashing. They have a machine surface on them that is the first thing to engage the ...
Genunine Rover sintered baulk ring. Use our 22G2033EVO sintered baulk ring, which is the best quality standard baulk ring currently in the market place and as used in our 5 speed gearboxes.
Our 22G2033MS are also si...
Mini Spares Performance Baulk ring.
The standard sintered baulk (synchro) rings are not tough enough for the demands of performance useage, in many instances lasting only one race before failure or breakage. The main reason is the incompat...
Straight cut gear set as designed by Special Tuning which contains only the -laygear,1st Motion shaft,2nd and 3rd gears. Not only does the straight cut design provide more strength and take significantly less power to drive but the ratios of the var...
Straight cut laygear for SC/CR 3-sync gearbox.teeth count 13-17-20-23
24 tooth straight cut gear as per original Special Tuning ratio. Beware a company has made a 25 tooth gear giving a dumb ratio.
Originally sprite and mini straight cut gears were the sam but with modern technology it was found smal...
1st motion (input) shaft for 3-sync straight cut/close ratio gearboxes.
22 teeth
Minispares were the first company to produce these layshafts for performance engine/gearboxes as the standard type would flex and result in the breakage of the bearings causing seizure. Produced in an upgraded material and heat treated to the correct...
Straight cut gear set as designed by Special Tuning which contains only the -laygear,1st Motion shaft,2nd and 3rd gears. Not only does the straight cut design provide more strength and take significantly less power to drive but the ratios of the var...
Mini Spares genuine part, made for reliability, because the current Rover 22G2033version is not good enough. These specials are CNC grooved for correct shape and machined for concentricity using the original type fixings to get the corr...
Synchromesh spring for the 3 synchro gearbox. Fits 1st/2nd and 3rd/4th hub.
3 required per hub and 6 per gearbox.
This little roller bearing goes inside the end of the 1st motion shaft on minis with 14mm mainshaft which it sits on.
This bearing was previously part number 88G409 and a true Rover replacement, but if you have earlier A type gears with the...
Mini Spares Performance Baulk ring.
The standard sintered baulk (synchro) rings are not tough enough for the demands of performance useage, in many instances lasting only one race before failure or breakage. The main reason is the incompat...
Inside your gearbox synchro hubs are 3 springs and these ball bearings to lock it in and out of gear. Often pop out and get lost when splitting the inner and outer hub.
When in doubt replace it. You have heard this many times but you better believe it on this part. If you have not personally just replaced these layshaft bearing then do it now while you have the chance. These bearing will destroy the inside of a very...
32 tooth first gear outer track only, for the sprite/midget 3 synchro gearbox.
This part number was for complete 1st gear hub assembly originally and the outer track was 22G1119 but when Rover stopped production we used this same number for<...
Gearbox gasket for the large alloy end cover which also houses the speedo drive pinion for all years of mini. The small gasket on the alloy housing with 2 bolt holes is GUG705564GM and the small pear shaped speedo housing gasket is [link...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.