£95.25 exc vat
£114.30 inc vat
£95.25 exc vat
£114.30 inc vat
Recommended usage 1 x C-22G1048 to fit one mini.
If you are serious about racing you must have straight cut gears. The primary benefit comes from the ratios availability; anytime you can keep the engine in the real torque curve, you've won the race!
The stock helical "S" box has a first ge...
STRAIGHT CUT 1ST GEAR FOR 4 SYNC SPECIAL TUNING GEARSET. £54.35 exc vat £65.22 inc vat
See table of "Straight Cut Gear Kits" and their components
Straight cut laygear for SC/CR 3-sync gearbox.teeth count 13-17-20-23
Made especially for the Spridgets to overcome junmping out of gear where hubs or selectors are worn, this is the same original ST ratio but with slightly different dog teeth design. Same for 2nd and 3rd.
24 tooth straight cut 3rd gear 3 synchromesh Mini only.Beware a company has produced a 25 tooth variety which is a dumb ratio
In 4 synchro gearbox it's a critical part of the close ratio gear set. Be sure to check your old one for wear on the inner surface of the layshaft bearings; it wears out far faster than the gear teeth! Pre A+.For A Plus see C-22A1737A 15...
STRAIGHT CUT 3RD GEAR FOR 4 SYNC SPECIAL TUNING GEARSET
If you are about to undertake a gearbox strip down and you are using an old Haynes manual beware. When locking the gearbox into 2 gears to undoe the large mainshaft and Ist motion nuts,...
straight cut reverse gear for the 4 synchro Pre Rod chabge gearbox we use the 16 and 18 teeth pattern for longevity. £42.09 exc vat £50.51 inc vat
See table of "Straight Cut Gear Kits" and their components
Idler gear conversion for straight cut drop gearsets only. This set up is for Pre A plus idler gearbox cases only and uses a roller bearing centrally unlike the old timken conversion which had taper bearings either end.
<...
Evolution Straight cut 25 tooth input/broach gear. Usually has one large marking ring on flange.
Achievable drop gear ratios when using our Evolution gears:
22 tooth primary - 30 tooth idler - 25 ...
Evolution Straight cut 24 tooth input gear. Usually has 2 identification rings on gear teeth.
Achievable drop gear ratios when using our Evolution gears:
22 tooth primary - 30 tooth idler - 25 too...
Straight cut gear set as designed by Special Tuning which contains only the -laygear,1st Motion shaft,2nd and 3rd gears. Not only does the straight cut design provide more strength and take significantly less power to drive but the ratios of the var...
Mini Spares best quality complete gasket and seal kit for engine block and gearbox,for all common engine types and sizes.
Also comes complete with Mini Spares Evolution clutch oil seal 13H2934MS, differential oil seals...
Mini Spares genuine part, made for reliability, because the current Rover 22G2033version is not good enough. These specials are CNC grooved for correct shape and machined for concentricity using the original type fixings to get the corr...
The plastic bush at the base of the gear lever stalk ON REMOTE TYPE GEARBOXES ONLY--stops that rattling noise
fit to the gearlever, not the knuckle joint, if it falls of the gear lever there will be a lot of play
Synchromesh spring for the 3 synchro gearbox. Fits 1st/2nd and 3rd/4th hub.
3 required per hub and 6 per gearbox.
Single roller bearing that only fits 3 synchro gearboxes to hold the 1st motion shaft-sporadic stocks only of these bearings as they went obsolete in 2008. These are genuine NSK bearings
Hardened flat washer to be used with flange type LSD Hardy Spicer C-BTA1262 outputs.