£334.82 exc vat
£401.78 inc vat
In stock
The stock helical "S" box has a first ge...
£334.82 exc vat
£401.78 inc vat
In stockRecommended usage 1 x C-AJJ3371 to fit one mini.
Mini Spares Performance Baulk ring.
The standard sintered baulk (synchro) rings are not tough enough for the demands of performance useage, in many instances lasting only one race before failure or breakage. The main reason is the incompat...
Mini Spares product Available again- 3 synchro B type gearbox 1st and 2nd synchro hub assembly for the mini. BEWARE -the outer track from the Sprite (22G1119) part of [link]22G1118[/link} is not reliable enough in a Mini gearbox as it allows balls an...
1st motion (input) shaft for 3-sync straight cut/close ratio gearboxes.
22 teeth
24 tooth straight cut 3rd gear 3 synchromesh Mini only.Beware a company has produced a 25 tooth variety which is a dumb ratio
Straight cut laygear for SC/CR 3-sync gearbox.teeth count 13-17-20-23
Straight cut gear set as designed by Special Tuning which contains only the -laygear,1st Motion shaft,2nd and 3rd gears. Not only does the straight cut design provide more strength and take significantly less power to drive but the ratios of the var...
Minispares were the first company to produce these layshafts for performance engine/gearboxes as the standard type would flex and resullt in the breakage of the bearings causing seizure. Produced in an upgraded material and heat treated to the correc...
24 tooth straight cut 3rd gear 3 synchromesh Mini only.Beware a company has produced a 25 tooth variety which is a dumb ratio
Evolution Straight cut 24 tooth input gear. Usually has 2 identification rings on gear teeth.
Achievable drop gear ratios when using our Evolution gears:
22 tooth primary - 30 tooth idler - 25 too...
Special circlip to hold the hardy spicer output shaft into the LSD units
such as evolution and Salisbury.
straight cut reverse gear for the 4 synchro Pre Rod chabge gearbox we use the 16 and 18 teeth pattern for longevity. £42.09 exc vat £50.51 inc vat
See table of "Straight Cut Gear Kits" and their components
Competition crownwheel bolt for use with our LSD crownwheels, these are CNC machined from EN24T with a reduced head height for more gearbox clearance.
Secondhand (used unit)only. This sits under the 28G251(DAM8488) alloy housing where the speedo cable connects to on the gearbox and the speedo drive pinion slots through this.Obsolete from Rover we are offering these old used units in ca...
Left hand differential lock tab as used on rod change boxes up until 1982 when they were not longer used. For R/H locktab see 22A962
Right hand differential lock tab as used on rod change boxes up until 1982 when they were not longer used.
Mini Spares best quality complete gasket and seal kit for engine block and gearbox,for all common engine types and sizes.
Also comes complete with Mini Spares Evolution clutch oil seal 13H2934MS, differential oil seals...
Mini Spares genuine part, made for reliability, because the current Rover 22G2033version is not good enough. These specials are CNC grooved for correct shape and machined for concentricity using the original type fixings to get the corr...
Complete bolt kit to bolt the transfer case and clutch cover onto the engine block.
Genuine Rover fibre type are now 48 thou thick which is so tight it will probably lock your diff up, they used to originally be .035 thou. These are 43 thou oversize type for worn units but the correct size of 35 thou is available as BTA101<...
The plastic bush at the base of the gear lever stalk ON REMOTE TYPE GEARBOXES ONLY--stops that rattling noise
fit to the gearlever, not the knuckle joint, if it falls of the gear lever there will be a lot of play
GAITER OVER THE END OF THE LEVER TO CASE ON MAGIC WAND GEARLEVER - 3.5"(90mm)wide-not for remote type gearbox with magic wand as fitted to base models and vans from 1968-75.For remote type magic wand cars see 22A1380 which is about 21mm ...
Mini Spares product Available again- 3 synchro B type gearbox 1st and 2nd synchro hub assembly for the mini. BEWARE -the outer track from the Sprite (22G1119) part of [link]22G1118[/link} is not reliable enough in a Mini gearbox as it allows balls an...
A plus crownwheel and pinion with 59 teeth and 19 teeth respectively=3.105
