USED CROWNWHEEL(62 TOOTH) A PLUS VERSION
DAM2677

($40.00) £40.00 exc vat

($48.00) £48.00 inc vat

Out of stockOut of stock
USED ONLY-this is the later A Plus 62 tooth gear for the 3.44 crownwheel and will only mate up with the correct 18 tooth pinion DAM2679. A kit of pre A plus gears are avaiable as CWP3-4

($40.00) £40.00 exc vat

($48.00) £48.00 inc vat

Out of stockOut of stock

Differential - Qty 1
Final drive ratios and Five Speed Gearbox - Qty 1

Alternative products

Stronger PRE a PLUS with 62 tooth crownwheel plus the 18 tooth pinion making a 3.444 diff ratio as used on Cooper S, plus many 998cc cars from 1970 on.

People also bought products

the correct pinion with 18 teeth to go with DAM2677 crownwheel on A plus set ups. Has a single offset to one edge identification groove mark.

The early pre A plus pinion was 22A413

17 teeth central groove...

Output drive shaft from the differential on Rod change type gearboxes,the teeth very rarely wear badly but the side cover bushes(2A3538)sometimes ruin the shaft causing those dreaded oil leaks from the seals in the output covers CHM85.

these...

The gearbox diff side plate bonze colour bush for all except auto and cooper S with hardy spicer output shafts. Sold singly 2 required per gearbox.

clearance needs to be 0.03mm

Bronze type bush is in the centre of all crownwheels in the gearbox plus another one is in the differential case opposite the end the crownwheel fits.

The bush after fitting will need to be reamed. Ream to 26.16mm 1.03"

Full rebuild kit with diferential parts with standard layshaft.

Using only the original manufacturers of the bearings such as RHP because all the Budget bearings are not good enough for longevity or performance use.

This is a full...

Inside your gearbox synchro hubs are 3 springs and these ball bearings to lock it in and out of gear. Often pop out and get lost when splitting the inner and outer hub.

smaller of the 2 shims at the ends of the laygear on the layshaft. These are sized accordingly and fit the first gear end --See DAM3180/1/3 for alternative sizes

This kit consists of one alloy sleeve with a groove on the outside to locate the O ring, the new "O" ring, a rod seal and a gaiter. To fit the kit simply remove the old gaiter if fitted and then the old oil seal. Fit the sleeve with the "O" ring fitt...

Gearbox differential pinion locktab to secure it on the mainshaft for all manual gearboxes.

This pin joins the gear change rod to the selector rod, behind the diff housing

case and is usually easier to remove when reverse is selected.In reverse gear the angle is easier for removal. This is a great time to fit the Mini Spares slick ...

A Plus 2nd gears are marked with a single identification groove.

If you are about to undertake a gearbox strip down and you are using an old Haynes manual beware. When locking the gearbox into 2 gears to undo the large mainshaft and 1st moti...

Genuine Mini Spares product. Spacer fits up against the primary gear on the crankshaft and held on by the "C" washer 22A319 - both these parts wear as well as the gear. Now made 2 thou oversize to help corect wear issues.

Only f...

Minispares recommend this central oil pick-up be installed with every transmission rebuild.

The original Mini oil pick-up pipe lives in the right hand edge of the gearbox casing, which is okay if you are driving straight. But during a right ...

Only for the 4 synchromesh gearbox synchroniser gear hub. There are 3 of these per hub with BLS107 ball bearing.

Locktab for holding the broach gear to the 1st motion shaft.