($35.16) £35.16 exc vat
($42.19) £42.19 inc vat
In stock
Fitted to 998/1100cc from 1979 and 1275GT from 1974
Kit contents are,
3H2127EVO Timing chain
88G561 Oil seal
12G2625 Gasket
12G2621 Tensioner
12G2628 Plate to hold tensioner
12G2629 Pin to hold tensioner/plate
($35.16) £35.16 exc vat
($42.19) £42.19 inc vat
In stockRecommended usage 1 x MSSK051EVO to fit one mini.
This kit consists of one alloy sleeve with a groove on the outside to locate the O ring, the new "O" ring, a rod seal and a gaiter. To fit the kit simply remove the old gaiter if fitted and then the old oil seal. Fit the sleeve with the "O" ring fitt...
This pin holds the tensioner 12G2628 for cars with single chain timing gears from 1980 on. You can tell if your car has this set up because the timing cover has a large bulge to accommodate this set up. Started on engine numbers 99H791 9...
Timing cover gasket with 11 holes for cars with timing chain tensioner bulge as standard on all A Plus. We recommend fitting the more expensive original genuine type with anti leak seal for longevity see GUG705550GM.
Pre A plus ...
Plastic tensioner pad to take up the slack in single row timing chains on A plus engines that wears and should be replaced nearly every time you have the timing cover off. From engine numbers 99H791/10H791 AND ALL A+. Fitted to 998/1100cc from 1979 a...
Genuine Mini Spares Original black timing cover oil seal for all A series until the introduction of a new type of lip seal introduced in 1991 mainly for injection engines, when they changed to LUF10006--albeit many owners fit this not kn...
Special superb extra strong timing chain with very limited stretch using modern day materials and technology to keep your timing correct and will fit any A series engine using a single row chain.
This chain saves all the time and effort requ...
A kit to convert the early style cartridge oil filter to the later style spin on filter.
Victor Reinz large bore head gasket for A-series engines.
Ramair’s hugely successful range of filter kits, designed to bolt directly to the carburettor body, is used widely in both competition and street applications. The element is of sturdy construction, supported by a stainless steel cage and provides ma...
Ramair’s hugely successful range of filter kits, designed to bolt directly to the carburettor body, is used widely in both competition and street applications. The element is of sturdy construction, supported by a stainless steel cage and provides ma...
Victor Reinz/Mahle small bore head gasket for A-series engines.
Gasket fitment. Writing side up.
New competition valve cotter for early heads with the large single groove valve, these are precision CNC machined from 4340 and heat treated to a better spec than EN24T and claimed to be stronger in fatigue life.
These locate better in the v...
Spring seat shims (set of 4), 0.020" thick (0.5mm).
Spacer shims to increase valve seat pressure and overall spring rate.
These were also used on all the 8 port head valve seats to prtect the alloy seats from wear. (8 port now C-AHT...
Timing cover front plate and tensioner plate bolt and washer kit. Comes with all parts to fit the cover except for the counter sunk screws if fitting a duplex kit (our duplex kits all come with these).
This is the large seal for the early type oil filter assembly pre spin on type.
Genuine Bosch lambda sensor, fitted to both the twin and single point injection cars and fitted in the same exhaust manifold shared by both cars. Be warned the cheaper non branded sensors cause lots of issues hence we only sell the Bosch version.
Fitting kit comprising of studs, nuts, plain washers, spring washers and a gasket
These Swiftune die cast performance pistons are part of their new Heritage range and are manufactured by global leading F1 German piston manufacturer Mahle. These pistons have been developed using their 50 plus years of experience. Glyn Swift was usi...
These Swiftune die cast performance pistons are part of their new Heritage range and are manufactured by global leading German F1 piston manufacturer Mahle. These pistons have been developed using their 50 plus years of experience.
Glyn Swif...
Replacement O ring for the Minispares range of chrome dipticks
This kit of head studs is the best available for road and lightly tuned engines. See the C-AHT280 set for highly tuned engines.
The material spec is alloy steel heat treated to 75 tensile tons per square foot minimum and finish...
You should replace the camshaft bearings every time the block goes to the machine shop. These bearings fit all late model 1275cc blocks (the ones without tappet covers on the back) It's almost too simple and thus often overlooked during a rebuild. Ca...
Race quality Single piston ring pack for Mini Spares Evolution Pistons which also fits Mega and Omega pistons. This uses 3 piece oil ring 4mm and 2 of 1.2mm compression ring.
Sold per piston so 4 packs required per engine.
Stabiliser bush kit for lower engine steady
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.