WATER TEMPERATURE CAPILLARY TYPE GAUGE BY TIM
TIM005

($35.10) £35.10 exc vat

($42.12) £42.12 inc vat

In stockIn stock
Mechanical movement with 57" long capillary tubing and has 40-120 degree centigrade calibration.



Recomended to use a TE5 adaptor.

($35.10) £35.10 exc vat

($42.12) £42.12 inc vat

In stockIn stock

Recommended usage 1 x TIM005 to fit one mini.

People also bought products

Electrical oil temperature gauge including sender. Sender is 1/8NPT fitting, comes with a variety of adaptors but you will need HPS8 a 5/8 UNF male to 1/8NPT adaptor and 2 AED172 if fitting to the sump.

Male to female brass spacer/adapter for mechanical water temp guage screws into head & accepts capillary tube. Required for SIB422 and SIB422MG. Also fits in MOCOT1

0-110 centigrade scale with 6 foot capillary mechanical fittings, requires an adaptor TE5 in order to fit the cylinder head.

Electrically operated gauge with 40-120 centigrade reading for negative earth cars only. Comes complete with sensor and relevant adaptors to fit the cylinder head.

You will require a HPS8 union for the sump plug hole if you are fitting this to the gearbox. If fitting to MOCOT2 you will require TE5 See SIB420MG also.

A sensible edition to any tuned min...

A union to fit the sump plug hole to accept Smiths oil temperature gauges, but will only take the small capillary type bulb as used on very early and current smiths oil temp gauges, does not fit the larger capillary fitted to some smiths gauges unles...

Combined water temperature and oil gauge in fahrenheit and 1-100lb oil pressure. This is a mechanical type(capillary fittings) with Smiths name on white face. Black face version avaiable as SIB130 Requires TE5 adaptor.

Sealing washer for the oil gauge to oil pipe as sold in OL kit and for 21A804 metal pipe to oil gauge.

Voltage stabiliser for clubman/2-3 clock side pod(smiths) up to 1988. Three terminals/br1303/20.

With this large diameter line to the oil pressure guage you can actually see minor fluctuations in the pressure at idle or when the relief valve bounces open and closed. Because the braided steel line is one piece from the block to the gauge there is...

Angled oil pipe adaptor for fitting in confined spaces to eradicate damage of oil pipe, requires an OA adaptor if being used with a oil pressure gauge/t-piece.

Oil pipe in plastic 5 feet long, if fitting to a Tim gauge you will require LMA017 adaptor for the gauge.

Not comppatable with the CAM6431 standard oli pressure block union, and OA shoudl be purchased to fit.

Oil gauge adaptor for fitting into engine block or T piece.

29" long for L/H/D cars from about 1988 on when Seiko nippon speedo gauges are fitted. earlier cars used a 33" cable GSD102 which had the grey end but are interchangable and cheaper.

A must if you want to run a mechanical oil gauge and retain the oil warning switch. Screws straight into the block on all A series engines.

Speedometer cable, 30" long for Smiths type central speedo-original was 26" long

Mini Moke Speedo Cable for the Centre clock type speedo,also 13" longer to allow the Smiths type central speedo to be moved.

You will need this union for your Tim gauge if you fit a replacement plastic oil pipe part number OL

Oil pressure is the "blood pressure" of your engine! Know how it is doing and you know how your engine is doing. This Smith's gauge is the standard 2" diameter with chrome bezel. With a magnolia face. Mechanical.

Does not come with pipewor...

Extra long cable for Smiths central located speedo when position moved in dash and also used as a Tacho cable for Sprite, 36" long.