998 23 TOOTH PRIMARY GEAR STRAIGHT CUT
C-STR223

£112.00 exc vat

£134.40 inc vat

In stockIn stock
S/C 23 tooth primary gear, with floating inner bush

£112.00 exc vat

£134.40 inc vat

In stockIn stock

Recommended usage 1 x C-STR223 to fit one mini.

People also bought products

Fully floating primary gear bush to downsize from our 1275cc type to 998 size on our 1275 primary gears with circlip conversion only to fit small bore crankshafts. Mainly used for our straight cut primary gear with circlip to hold fully floating bush...

24 tooth primary gear bush for small bore applications, with floating bush

Evolution Straight cut 25 tooth input/broach gear. Usually has one large marking ring on flange.





Achievable drop gear ratios when using our Evolution gears:



22 tooth primary - 30 tooth idler - 25 ...

S/C 30 tooth idler gear for A+ boxes using the 7/8" shaft.





Achievable drop gear ratios when using our Evolution gears:



22 tooth primary - 30 tooth idler - 25 tooth input = 1.136-1


24...

Minispares were the first company to produce these layshafts for performance engine/gearboxes as the standard type would flex and resullt in the breakage of the bearings causing seizure. Produced in an upgraded material and heat treated to the correc...

For all rod change gearbox mechanism housings, this as un uprated poly bush replacement for the standard rubber bonded mount

Mini Spares best quality complete gasket and seal kit for engine block and gearbox,for all common engine types and sizes.



Also comes complete with Mini Spares Evolution clutch oil seal 13H2934MS, differential oil seals...

Quick release rod change gear coupling a direct replacement for the standard item, doing away with the troublesome roll pins. It comes complete with high quality quick release clips

Originally developed by Rover to cut down on warranty hourly costs on powertrain warranty repairs, by their main dealers.-Labour time allowed at Rover dealers for fitting this seal was 3.4 hours labour rate.

This is a special rigid seal and ...

New Minispares Evolution straight cut crownwheel and pinion set 3.47. The crownwheel in these kits has a 20% wider gear than previously supplied, and a pinion made from Aero quality steel making it 20% tougher.17/59 teeth cont

Not for LSD se...

Primary gear thrust washers are made in varying sizes to take up the play.

Standard gap size should be between 3-6 thou. These are for the 850/998/1098cc

engines with 22A1493 Deva bush primary gear. Early 850cc had thin...

THIS BEARING HAS PRE A+ INNER DIAMETER AND A+ OUTER DIAMETER. If you have the large A plus idler gear bearing hole and want to use it for the earlier pre A plus small hole type idler gear then this bearing is what you require to sleeve it down in siz...

Mini Spares own Evolution limited slip diff with over 10 years success

No serious competitor would use a Mini on a race track or autocross course without a limited slip differential should the rules allow it. This original Mini Spares Ev...

Magnetic drain plug, plus added length to help gather all those metal bits between oil changes. For all manual Mini's.

These are the later A+ type spec which rover superseded to when upgrading the idler gear material on injection cars. See workshop manual for shimming details.

The idler gear in all Mini power units must be set with great care. The thrust wa...

Genuine 1ST Motion shaft SINGLE track original bearing for 4 synchromesh 1st motion shaft.

This is a Genuine RHP bearing, and should not be confused with cheap alternatives. The cheap aftermarket bearings often fail and the work involved to...

Full rebuild kit less diferential parts.

Using only the original manufacturers of the bearings such as RHP because all the Budget bearings are not good enough for longevity or performance use.

This is a full kit of bearings except...

Mini Spares Performance Baulk ring.

The standard sintered baulk (synchro) rings are not tough enough for the demands of performance useage, in many instances lasting only one race before failure or breakage. The main reason is the incompat...

Genuine RHP as originally fitted to every production Mini.

Two of these main diff carrying bearings are required in the gearbox and this new steel caged type fits either way round. Should be pre loaded by 1-2 thou.

Some original fi...