998 24 TOOTH PRIMARY GEAR STRAIGHT CUT
C-STR224

£105.00 exc vat

£126.00 inc vat

Out of stockOut of stock
24 tooth primary gear bush for small bore applications, with floating bush

£105.00 exc vat

£126.00 inc vat

Out of stockOut of stock

People also bought products

Fully floating primary gear bush to downsize from our 1275cc type to 998 size on our 1275 primary gears with circlip conversion only to fit small bore crankshafts. Mainly used for our straight cut primary gear with circlip to hold fully floating bush...

S/C 23 tooth primary gear, with floating inner bush

Evolution Straight cut 25 tooth input/broach gear. Usually has one large marking ring on flange.





Achievable drop gear ratios when using our Evolution gears:



22 tooth primary - 30 tooth idler - 25 ...

S/C 30 tooth idler gear for A+ boxes using the 7/8" shaft.





Achievable drop gear ratios when using our Evolution gears:



22 tooth primary - 30 tooth idler - 25 tooth input = 1.136-1


24...

Minispares were the first company to produce these layshafts for performance engine/gearboxes as the standard type would flex and result in the breakage of the bearings causing seizure. Produced in an upgraded material and heat treated to the correct...

Straight cut gearset for A+ gearbox's using the standard 1st and reverse gear. UK made -The ultimate for TUNED street cars or clubman events giving nearly the same close ratios as the original 3 synchro straight cut gear set.

Using latest g...

LAYGEAR STRIGHT CUT FOR A PLUS GEARBOX IN ORIGINAL ST RATIO

TOOTH COUNT 15-19-23-25---this takes 2-CHM141 bearins

See table of "Straight Cut Gear Kits" and their components

Left hand differential lock tab as used on rod change boxes up until 1982 when they were not longer used. For R/H locktab see 22A962

Right hand differential lock tab as used on rod change boxes up until 1982 when they were not longer used.

Mini Spares genuine part, made for reliability, because the current Rover 22G2033version is not good enough. These specials are CNC grooved for correct shape and machined for concentricity using the original type fixings to get the corr...

Extra strong magnetic sump plug. This high quality plug is constructed from 303 stainless steel and houses the latest Neodymium magnet which is currently the strongest available to give the best protection for your engine, even more important when yo...

Quick release rod change gear coupling a direct replacement for the standard item, doing away with the troublesome roll pins. It comes complete with high quality quick release clips

Originally developed by Rover to cut down on warranty hourly costs on powertrain warranty repairs, by their main dealers.-Labour time allowed at Rover dealers for fitting this seal was 3.4 hours labour rate.

This is a special rigid seal and ...

Oil seal for speedo drive pinion cover (DAM8488)

New Minispares Evolution straight cut crownwheel and pinion set 3.47. The crownwheel in these kits has a 20% wider gear than previously supplied, and a pinion made from Aero quality steel making it 20% tougher.17/59 teeth cont

Not for LSD se...

Genuine Mini Spares product, 2nd gear 4 synchro Pre A Plus-26 teeth

If you are about to undertake a gearbox strip down and you are using an old Haynes manual beware. When locking the gearbox into 2 gears to undo the large mainshaft and Ist m...

Primary gear thrust washers are made in varying sizes to take up the play.

Standard gap size should be between 3-6 thou. These are for the 850/998/1098cc

engines with 22A1493 Deva bush primary gear. Early 850cc had thin...

The shims go against the mainshaft double roller bearing securing cap in your gearbox to give it pre load. See workshop manual for advice but you are aiming for only 1 thou pre load.

The gasket with the oil suction seal hole fits every mini gearbox case and the other two are for the different case shapes, one for 3 synchro case and one for 4 synchro gearbox case, so choose the one you require. For latest spec Klinger gasket set u...

Actually the concertina dust cover for the rod change oil seal to prevent road debris attacking the seal. See MSSK050 kit when undertaking this job.