£19.13 exc vat
£22.96 inc vat
Out of stock
Sometimes a little tight in the 2A3624 housing, just rotate to loosen up.
It has 16 teeth and was used on 3.4 final drives with 2A3720 drive spindle which had 6 teeth. Usually from 20.50mm to 21.12mm wide
The DAM8074 worm used on the ERA Mini also had 16 teeth but yellow in colour but used a 5 tooth drive and has been used as it has about same diameter of 20.4mm.
BEWARE-There was also a different green (17) tooth drive DAM2904 which was fitted to the MG Metro with 3.4 diff and can be used in place of 22A1881 for all early minis.
plastic worm gears used on production minis.
15 teeth TXD10004 black worm
16 teeth DAM2905 green worm
17 teeth 22A1881 clear/white worm
18 teeth TXD10006 grey worm special size
£19.13 exc vat
£22.96 inc vat
Out of stock
Follow your speedo cable to the gearbox and it screws onto an alloy housing bolted to the gearbox. This is the gasket between the housing and the gearbox.
for the inspection plate on the front cover of the transmission where the speed cable goes to -it has 2 bolt holes cut out
Secondhand (used unit)only. This sits under the 28G251(DAM8488) alloy housing where the speedo cable connects to on the gearbox and the speedo drive pinion slots through this.Obsolete from Rover we are offering these old used units in ca...
Ultimate helical gear kit for strength, includes special laygear,1st motion shaft, 2nd and 3rd gears to mate with the other standard parts in your gearbox to provide you with a stronger quieter gearbox and 4 synchromesh heavy duty clubman ratio kit. ...
Genuine Mini Spares product, 2nd gear 4 synchro Pre A Plus-26 teeth
If you are about to undertake a gearbox strip down and you are using an old Haynes manual beware. When locking the gearbox into 2 gears to undo the large mainshaft and Ist m...
THIS BEARING HAS PRE A+ INNER DIAMETER AND A+ OUTER DIAMETER. If you have the large A plus idler gear bearing hole and want to use it for the earlier pre A plus small hole type idler gear then this bearing is what you require to sleeve it down in siz...
The shims go against the mainshaft double roller bearing securing cap in your gearbox to give it pre load. See workshop manual for advice but you are aiming for only 1 thou pre load.
Genuine 1ST Motion shaft SINGLE track original bearing for 4 synchromesh 1st motion shaft.
This is a Genuine RHP bearing, and should not be confused with cheap alternatives. The cheap aftermarket bearings often fail and the work involved to...
This little roller bearing goes inside the end of the 1st motion shaft on minis with 14mm mainshaft which it sits on.
This bearing was previously part number 88G409 and a true Rover replacement, but if you have earlier A type gears with the...
Mini Spares Performance Baulk ring.
The standard sintered baulk (synchro) rings are not tough enough for the demands of performance useage, in many instances lasting only one race before failure or breakage. The main reason is the incompat...
Genuine RHP as originally fitted to every production Mini.
Two of these main diff carrying bearings are required in the gearbox and this new steel caged type fits either way round. Should be pre loaded by 1-2 thou.
Some original fi...
The bronze washer for the planet gears in the differential for pre A plus gearbxes. You can use the DAM5071 and cut the lips off.
Stud to hold the clutch case to the engine and gearbox, 3 of required. 5/16"UNC thread for alloy fitment for gearbox with UNF thread the other end for the nuts. These are 1.5"long.
The 6 longer ones are 22A152.
These st...
Minispares were the first company to produce these layshafts for performance engine/gearboxes as the standard type would flex and resullt in the breakage of the bearings causing seizure.Produced in standard material heat treated to the correct core d...
Torrington/Koyo idler gear bearing with special rollers for allowing movement on late type idler gears. The idler gears for twin point cars were also made from clean steel as an upgrade from 1996 on. This special bearing replaces the cheaper inferior...
Bearing 26.9mm wide to take 19.05mm idler gear shaft that fits in the gearbox case and clutch housing case on 4 synchro gearboxes until introduction of A plus when a larger bearing was fitted.
When in doubt replace it. You have heard this many times but you better believe it on this part. If you have not personally just replaced these layshaft bearing then do it now while you have the chance. These bearing will destroy the inside of a very...
smaller of the 2 shims at the ends of the laygear on the layshaft. These are sized accordingly and fit the first gear end --See DAM3180/1/3 for alternative sizes
Genuine new 6 tooth speedo drive spindle that mated with 17 tooth speed pinion 22A1881 on cars with 10" wheels before 1980 plus any year 1275GT. Also 12"wheel cars with 3.44 final drive 1984 on. On the Metro mini this was used with 17 an...
Bolts with the large diameter shoulder on the shank for either the stock remote shift sandwich mount or C-22G245.
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.