£15.60 exc vat
£18.72 inc vat
Out of stock
these used pinions have not been fully cleaned so please CLEAN TEETH BEFORE FITTING. new ones are no longer available
£15.60 exc vat
£18.72 inc vat
Out of stock
:USED: Speedo cable drive pinion in the gearbox with 17 teeth, it was used with a 6 tooth drive spindle on all 10" wheel cars pre 1980.
Either brown or plain white sort of colour about 20.50mm to 21.12mm in diameter and very similar to [lin...
Left hand differential lock tab as used on rod change boxes up until 1982 when they were not longer used. For R/H locktab see 22A962
Right hand differential lock tab as used on rod change boxes up until 1982 when they were not longer used.
Full rebuild kit with diferential parts with competition layshaft, our 22G2033EVO baulk rings and performance clutch oil seal 13H2934MS
Using only the original manufacturers of the bearings such as RHP because all t...
Extra strong magnetic sump plug. This high quality plug is constructed from 303 stainless steel and houses the latest Neodymium magnet which is currently the strongest available to give the best protection for your engine, even more important when yo...
Complete bolt kit to bolt the transfer case and clutch cover onto the engine block.
Quick release rod change gear coupling a direct replacement for the standard item, doing away with the troublesome roll pins. It comes complete with high quality quick release clips
NO LONGER MADE" see 22G2024MS for 18 tooth red Metro speedo pinion as used with 5 teeth drive,now obsolete from Rover but 22G2204MS is offered as used secondhand items in case ratios require changing. -Combinations are listed on our webs...
NLA see 22G2022MS:Used: (secondhand) 5 tooth drive spindle mainly used on Metro range but includes ERA turbo mini with 3.2 final drive using 16 tooth plastic pinion.
Obsolete new but offered "used" in case a ratio change is required. The on...
Originally developed by Rover to cut down on warranty hourly costs on powertrain warranty repairs, by their main dealers.-Labour time allowed at Rover dealers for fitting this seal was 3.4 hours labour rate.
This is a special rigid seal and ...
"USED" secondhand crownwheel and pinion 3.647 ratio "A" plus teeth. 17x62 teeth
Sold as seen,some with inner part of bearing still on crownwheel (if they come off without using a puller tool it usually means they have spun, ruining the seati...
New Minispares Evolution straight cut crownwheel and pinion set 3.75. The crownwheel in these kits has a 20% wider gear than previously supplied, and a pinion made from aero quality steel making it 20% tougher.16x60 teeth count.
Always Check...
Genuine Rover fibre type are now 48 thou thick which is so tight it will probably lock your diff up, they used to originally be .035 thou. These are 43 thou oversize type for worn units but the correct size of 35 thou is available as BTA101<...
The plastic bush at the base of the gear lever stalk ON REMOTE TYPE GEARBOXES ONLY--stops that rattling noise
fit to the gearlever, not the knuckle joint, if it falls of the gear lever there will be a lot of play
A plus crownwheel and pinion with 59 teeth and 19 teeth respectively=3.105
Minispares were the first company to produce these layshafts for performance engine/gearboxes as the standard type would flex and resullt in the breakage of the bearings causing seizure. Produced in an upgraded material and heat treated to the correc...
Genuine Mini Spares product, 2nd gear 4 synchro Pre A Plus-26 teeth
If you are about to undertake a gearbox strip down and you are using an old Haynes manual beware. When locking the gearbox into 2 gears to undo the large mainshaft and Ist m...
These are the later A+ type spec which rover superseded to when upgrading the idler gear material on injection cars. See workshop manual for shimming details
Quantity required is 2 per gearbox but the idler gear requires shimming for correct...
Hardened flat washer to be used with flange type LSD Hardy Spicer C-BTA1262 outputs.
The shims go against the mainshaft double roller bearing securing cap in your gearbox to give it pre load. See workshop manual for advice but you are aiming for only 1 thou pre load.
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.