OIL COOLER HOSE KIT MINI WITH INERTIA STARTER
MOC1013

£33.47 exc vat

£40.16 inc vat

In stockIn stock
For minis with original inertia type starter. The block hose is 12" long and the filter hose is 14". If you want longer hoses see clubman kit MOC100102 block hose 14.5" long and 24" long filter pipe. Pre engaged starter type cars upto 1992 require a longer hose kit MOC1015. Cars with a 12A engine number require MOC1014 .

If a pre engaged starter is fitted (integral solenoid) the oil cooler has to be mounted closer to the alternator resulting in longer pipes(MOC1015). A-series engines up to 1992 had a block union size of 5/8" UNF and filter head union size of 1/4" NPT.

From 1992 on, union sizes changed on all engines with a 12A prefix number and became universal at 11/16" UNF. The filter head for these is recognisable by casting part number LPX10027.

£33.47 exc vat

£40.16 inc vat

In stockIn stock

Recommended usage 1 x MOC1013 to fit one mini.
Oil Coolers / Oil Gauge Pipes & Oil Switches - Qty 1

Alternative products

Whether you are installing a cooler from scratch or merely need to replace your tired old rubber hoses, you'll like the looks of this stronger Braided hose kit. The hoses are fully assembled, with the proper fittings in place and even include the nec...

People also bought products

A kit to convert the early style cartridge oil filter to the later style spin on filter.

Victor Reinz large bore head gasket for A-series engines.

Original equipment quality for factory built engines giving longer life expectancy on road cars under variable conditions of oil and use. These are the 1275cc mains as fitted to A Plus engines with the locating tab in the middle rather than to the ou...

Victor Reinz/Mahle small bore head gasket for A-series engines.



Gasket fitment. Writing side up.

Replace with new camshaft,it's almost too easy to overlook during a rebuild. Camshaft bearings are pressed into the block and thus are usually done by a machine shop. You would not rebuild an engine without replacing the rod bearings, so why not the ...

Spring seat shims (set of 4), 0.020" thick (0.5mm).

Spacer shims to increase valve seat pressure and overall spring rate.

These were also used on all the 8 port head valve seats to prtect the alloy seats from wear. (8 port now C-AHT...

Timing cover front plate and tensioner plate bolt and washer kit. Comes with all parts to fit the cover except for the counter sunk screws if fitting a duplex kit (our duplex kits all come with these).

Fitting kit comprising of studs, nuts, plain washers, spring washers and a gasket

These Swiftune die cast performance pistons are part of their new Heritage range and are manufactured by global leading German F1 piston manufacturer Mahle. These pistons have been developed using their 50 plus years of experience.

Glyn Swif...

You should replace the camshaft bearings every time the block goes to the machine shop. These bearings fit all late model 1275cc blocks (the ones without tappet covers on the back) It's almost too simple and thus often overlooked during a rebuild. Ca...

Race quality single piston ring pack for Mini Spares Evolution Pistons which also fits Mega and Omega pistons. This uses 3 piece oil ring 4mm and 2 of 1.2mm compression ring.

sold per piston so 4 packs required per engine

ARP Head stud kit that compromises of;

4 x Long Head Studs

7 x Short Head Studs (Disregard 2 if you're using a 9 stud application)

11 x Multipoint ARP nuts

11 x Heavy Duty Washers

4 x Rocker post studs <...

Oil cooler union for later cars, will fit the oil filter head and block, 1/2" BSP to 11/16". Requires DSM18 to seal. These are handy when you have changed to a later filter head etc and want to fit an early oil cooler kit.

Mini Spares best quality complete gasket and seal kit for engine block and gearbox,for all common engine types and sizes.



Also comes complete with Mini Spares Evolution clutch oil seal 13H2934MS, differential oil seals...