£11.00 exc vat
£13.20 inc vat
now
£9.35 exc vat
£11.22 inc vat
In stock
£11.00 exc vat
£13.20 inc vat
now
£9.35 exc vat
£11.22 inc vat
In stockRecommended usage 1 x 21A1669 to fit one mini.
This bracket fits on the l/h rear hub assembly for the handbrake cable to pass through before entering the backplate.
Front subframe to front teardrop mounting, clutch case to block.
Engine mounting to subframe - easier to use than the GFK5184 - 3/4" long
Non spacered die cast alloy brake drums. The alloy material has a finned design that dissipates heat quicker which in turn helps reduce brake fade. Sold as a pair of drums.
Rubber gaiter to keep debris from entering the drum via the backplate handbrake lever SMN10005. Sold singly per backplate, 2 required per car.
Genuine AP Lockheed rubber boot
Die cast alloy brake drums with built in spacer-imported copy but have proven 100% reliable on sales from 1998 without any problems. The alloy material has a finned design that dissipates heat quicker which in turn helps reduce brake fade. While desi...
All MK3 minis to 1978 except Cooper S MK3 which used 21A1774.
Fitted mainly to cars with 3/4" larger bore rear wheel cylinders.
The correct regulator valve for all MK1/2 mini plus all Cooper S inc MK3 is 21A1774 where m...
Genuine AP brand new rear Left Hand back plate assembly (beware of copies).
These are ready to bolt on, brand new stock from AP Automotive and have the .75" bore genuine wheel cylinders GWC1102. Remember that all wheel cylinder ...
Genuine AP brand new rear right hand back plate kit (beware of copies).
These are ready to bolt on brand new stock from AP Automotive and have the .75" bore genuine wheel cylinders GWC1102. Remember that all wheel cylinder rubb...
Adjustable original brake proportioning/balancing valve for racers only.
The most common brake system on the Mini has Disc brakes in the front and drums in the rear. The weight bias on the car is all in the front and thus under hard braking...
Easy bend copper brake pipe 26" long with one female and one male end - used on hydrolastic cars from regulator valve to near side rear hose. These pipes are retail less 35% discount at least to keep prices viable.
A special 3/8" unf half nut (9/16"AF spanner size)for fitting on rear brake hoses and carbs to manifold.
If your rear brake drums have 1" built in spacers such as all Cooper S and any post 1984 minis, these are the longer drum retaining screws, 2 required per drum and sold individually.
Easy bend copper 24"long brake pipe with one female and one male end for the regulator on the rear subframe to the n/s/r hose on hydrolastic cars only.
Also used on split front to rear system with valve in engine compartment - from 3 way uni...
The screw that holds the drum on the hub. Earlier hubs had two screws, many replacements have only one, all that’s needed.
9/16"(0.565") bore rear wheel cylinder used from 1959-1967. This can be used for a replacement for GWC1134 also. The only difference is a locating dowel in the back of the cylinder which can easily be removed or the backplate drilled to ...
originally fitted to the 1275GT 1976/7 single line system plus NON UK 850/998 diagonal split systems for the same years --half inch bore size it was the smallest cylinder ever used--repair kit was BHM7015 which is now very scarce.Uses [l...
Mintex brake shoes for the rear of all minis which are 1.25" wide. Also fitted to front on early single leading shoe cars (dry suspension pre 1964) with a single wheel cylinder. Manufactured by Mintex and sold as a box set of 4 brake shoes for one re...
Rubber gaiter to keep debris from entering the drum via the backplate handbrake lever SMN10005. Sold singly per backplate, 2 required per car.
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.