£180.00 exc vat
£216.00 inc vat
In stock
The last few of them and this was their ultimate camshaft at the time, being a sprint cam but when used with injection was quite tame and drivable.
Cheaper than...
£180.00 exc vat
£216.00 inc vat
In stockRecommended usage 1 x C-AEG599 to fit one mini.
Timing belt camshaft drive systems have been around for a number of years, in fact for a lot longer than the life expectancy of the belts. If you have a belt drive conversion you should have one of these replacement belts. If you want to keep things ...
Adjustable cam gear set with non stretch chain. Cam gear weighs 674g
Even a stock camshaft needs to be timed correctly. If you want to get the maximum benefit from a "hot" cam it is doubly important that the cam timing be correct. This adju...
Spin on oil filter housing for performance engines-uses 88G402 gasket-made out of billet alloy it has a strong mating face to the block where oil leakage occurs from high revving engine vibrations, is slightly shorter offering more clear...
Extra length of 0.220" for 8 port Arden heads on 1275cc. Larger 6.35mm diameter 3 piece push rod (2 ends and 1 rod) which needs loctiting for safety although once fitted the parts cannot displace.
The larger diameter improves push rod rigi...
Lower Stabilizer Kit, RH.
Designed as an almost mandatory addition to any Mini with a rod change transmission, extra stabilizers will greatly aid any car. In stock form the control is left to the upper stabilizer. This often results in not o...
The oil pressure relief valve consists of an aluminum plunger with a heavy spring behind it. Access is through the 15/16" domed cap nut beside the dizzy. Once this nut is removed the spring will be visible. The plunger is beneath the spring and will ...
Set of 8, original leyland ST product but now made for us to our specification. Critical to the life and performance of the camshaft is the use of high quality cam followers. Remember, they operate in a finite hole and thus the dimensional tolerances...
NPR Ring set for 73.5mm Mega and Omega pistons with 1.2mm thick rings and 3 piece oil rings-also for new range of EVO pistons C-STN101
This thinner crankshaft oil seal was used on the later belt drive kits with a plastic cover and larger diameter crank gear
Lower Stabilizer Kit, LH.
Designed as an almost mandatory addition to any Mini with a rod change transmission, extra stabilizers will greatly aid any car. In standard form the engine control is left to the upper stabilizer. This often result...
Gasket for all spin on filter heads to block except aftermarket billet types which use 88G402. For the latest state of the art gasket material see GUG705553GM
Genuine Timing cover Klinger gasket with screen sealant strip to stop leaks for cars with timing chain tensioner bulge as standard on all A Plus.
Definitely worth the extra cost for longevity on your valuable classic mini
Tip-When ...
Sold as a single piston and although for Turbos is from original Rover casting and tooling to run on 5psi turbo boost. Now with 9.38cc. They use our mega ringset C-AJJ3379-40.
If using more boost you need to be working on a low...
Genuine Mini Spares engine front plate for A-Plus timing gear with a tensioner set up.
This plate has been modified by counter sinking the 2 main cap bolt holes to accept countersunk screws to give extra clearance and for those wishing to fi...
Brass type core plug for engine. Originally, engines had brass oilway plugs (2K1345) 1/4" hole fitted. These cup type plugs replaced them about 1985. 12.7mm cup type plug about 9.6mm deep. Fits 1/2" hole.
All good engine tuners ...
The ultimate cam follower with oil hole, designed to minimise float and jump normally seen in original cam followers, which ultimately loses power. Precision ground outside diameter with smaller chamfered base to give more surface area for extra hi l...
Billet steel CNC machined ultralight race backplate for pre verto clutches, weighs just 0.87kg.
MPI only. 3 YEAR GUARANTEE-UK made.Large impeller higher capacity water pump. Mini Spares procured product as original Rover Airtex tooling has been scrapped.
Fitted with a PPS, glass filled plastic impeller as used by Jaguar and Aston Marti...
3 YEAR GUARANTEE-UK made. Large impeller higher capacity water pump with a high quality die cast body. A Mini Spares procured product as the original superb Rover Airtex tooling has been scrapped.
Fitted with a PPS, glass filled plastic impe...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.