EXHAUST RC40 LARGE OUTLET SIDE BORE WITH FITTING K...

The famous RC40 Millennium range mild steel twin box exhaust with large bore outlet and side exit plus the fitting kit for the exhaust system.

£167.59 exc vat

£201.11 inc vat

EXHAUST RC40 WITH LARGE BORE OUTLET PLUS LCB AND F...

RC40PACKAGE008

The famous RC40 mild steel side exit large outlet exhaust with a new state of the arts exhaust manifold C-AEG364 plus the fitting kit for the exhaust system.

There is NOT enough clearance room when fitting to old ca...

£245.43 exc vat

£294.52 inc vat

POLYURETHANE REAR COTTON REEL EXHAUST MOUNT

GEX7251POLY

The very rear bobbin type mounting rubber on every mini made until the introduction of a rubber hanger strap in 1992. When the RC40 or similar systems are fitted, 2 will be required. This is a stronger poly version.

£2.70 exc vat

£3.24 inc vat

EXHAUST SLEEVE REDUCER PIPE 1.75" TO STANDARD BORE

LDP2

This sleeve will allow an 1"3/4 rear box to fit a standard bore front pipe of a 998cc mini. The large end fits into the RC40 and the smaller end accepts the 1.25" diameter as standard 850/998 exhaust pipe bore

£18.00 exc vat

£21.60 inc vat

MANIFOLD CLAMP 1.75" COOPER FREEFLOW WITH TAG FLAT...

C-AHT98

This is the clamp on the cooper freeflow manifold to clamp it to the engine for extra support, supplied with tag.

£4.95 exc vat

£5.94 inc vat

CATALYTIC CONVERTER NUT M10 METRIC

NV110051

THE M10 METRIC NUT THAT SCREWS ON THE THREAD BOLTS OF THE CATALYLITIC CONVERTER

£0.61 exc vat

£0.73 inc vat

EXHAUST U BOLT CLAMP 2 1/4" 58mm

GEX9011

£0.92 exc vat

£1.10 inc vat

EXHAUST CENTRE STRAP.SALOON

GEX7082

Exhaust centre strap that hangs from the mounting on the centre of the rear subframe, for saloon models only as the van is longer(GEX7273).

The clip on the exhaust that this attaches to is GEX7052 and is usually on a new exhaust...

£2.42 exc vat

£2.90 inc vat

EXHAUST MIDDLE MOUNTING

GEX7081

Middle exhaust mounting, bolts on to the front of the rear subframe and is the central or first of the rubber mountings. see GEX7081POLY for Poly type or if you are fed up with breakages see C-19G3257.The original Genuine pa...

£1.60 exc vat

£1.92 inc vat

EXHAUST HANGER BRACKET ON REAR OF REAR SUBFRAME

C-ARA671

This is a bolt on conversion bracket to fit on the rear of the rear subframe to take the later type rubber strap mounted exhaust systems.Later subframes 1991 on had these parts welded in position.

£12.96 exc vat

£15.55 inc vat

EXHAUST U BOLT CLAMP 1.1/4" 32mm

GEX9002

£0.68 exc vat

£0.82 inc vat

MANIFOLD TO DOWNPIPE EXHAUST CLAMP

GEX7046

Exhaust manifold to downpipe clamp.

The key to eliminating exhaust leaks at the manifold flange is the clamp. These new clamps include proper brass nuts and support washers. Fits most 850cc, 948cc, 998 etc. Those engines with single carb an...

£2.50 exc vat

£3.00 inc vat

MANIFOLD CLAMP FLAT TYPE 48mm 1.875"

C-AHT121

For the medium bore Maniflow LCB Y piece or AN180V. 48mm ID

£4.50 exc vat

£5.40 inc vat

COMPETITION EXHAUST MOUNTING ON FRONT OF REAR SUBF...

C-19G3257

The center exhaust hanger takes a lot of abuse during hard acceleration or if you're low enough to bottom out on bumps. This mount has a through metal bolt to keep it intact.

£4.00 exc vat

£4.80 inc vat

GASKET EXHAUST DOWNPIPE INJECTION

GEX7779

Special tin plate type of gasket that goes between the manifold and exhaust downpipes on all injection cars.

£1.68 exc vat

£2.02 inc vat

REAR COTTON REEL EXHAUST MOUNT

GEX7251

The very rear bobbin type mounting rubber on every mini made until the introduction of a rubber hanger strap in 1992. When the RC40 or similar systems are fitted, 2 will be required.

See C-19G3258 for larger upgrade...

£1.05 exc vat

£1.26 inc vat

EXHAUST U BOLT CLAMP 1 3/8" 35mm

GEX9003

£0.62 exc vat

£0.74 inc vat

EXHAUST REAR BRACKET 1275GT & S PLUS RC40 (REAR)

GEX7249

This is the hanger on the rear of the rear subframe for all Coopers and cars with an RC40 exhaust system. The u bolt to fix this to the exhaust is GEX9007.

All the parts to hang RC40 exhausts systems are available i...

£1.55 exc vat

£1.86 inc vat

MANIFOLD CLAMP 1.5/8" LCB (1.625") FLAT TYPE

C-AHT97

This popular size clamp fits the y piece where it joins the manifold on all our standard long centre branch exhaust manifolds. Sold singly.

£5.04 exc vat

£6.05 inc vat

MANIFOLD CLAMP 1.5" LCB TO ENGINE FLAT TYPE

C-AHT94

This is the clamp for the C-AEG365 manifold that clamps it to the engine for extra support.

£4.80 exc vat

£5.76 inc vat

EXHAUST MIDDLE POLY EXHAUST MOUNTING

GEX7081POLY

Mounting in poly for the exhaust on the front section of the rear subframe. Now orange in colour.

£7.13 exc vat

£8.56 inc vat

EXHAUST MOUNTING COMPETITION REAR EXHAUST

C-19G3258

Larger, stronger rear exhaust mounting as used by works cars will usually fit earlier subframes on existing holes in either the middle or side exit position.

£3.25 exc vat

£3.90 inc vat