WIRING MAIN LOOM 1984/WITH SIDE REPEATERS INERTIA ...
HAM3684

£236.02 exc vat

£283.22 inc vat

Out of stockOut of stock
Was HAM3066 main loom less the wing side repeaters but superseded by Rover to this loom with side repeaters on wing,although the manufacturer of these looms always added them to HAM3066 anyway -Inertia starter, Ballast coil, Instrument cluster in fro...

£236.02 exc vat

£283.22 inc vat

Out of stockOut of stock

Battery fittings, cables and main looms - Qty 1

Recommended products

A plastic lamp spade connection with sidelight bulb aperture for use on sealed beam units only. Uses a GLB501 capless bulb. The mini clubman used sealed beams but had independant side lamps and therefore had an equivalent unit less the s...

Rear body harness with speaker wires, known as thick wall type which was replaced by thin wall PVC covered wire type in 1989. AN169 is the thin wall equivalent and occassionly fitted or found on early cars wothout any problems.

...

People also bought products

Main wiring grommet that fits in the front parcel shelf. ID 12.5mm fits 35mm hole.

PVC loom for Portuguese built Mini Moke, comes complete front and rear.

Rear body harness with speaker wires,known as thin wall PVC type type which replaced the thick wall type in 1989. AN166 is the thick wall early equivalent.

If your car has no speakers just disregard the extra wires. This loom ha...

Rear body harness with speaker wires, known as thick wall type which was replaced by thin wall PVC covered wire type in 1989. AN169 is the thin wall equivalent and occassionly fitted or found on early cars wothout any problems.

...

You should always use this kit for fitting any auxiliary spot or fog lamps.

Kit contains wiring and safety relay-cheaper than a burnt out engine compartment.

Please note, SPI and MPI cars have this facility built as standard safety ...

Inertia starter -no side repeaters on wing -Instrument cluster in front of driver,either 3 clock with tacho or 2 clock cars but ignore wires from distributor for tacho and tacho wires.



On pre 1984 cars the wiring for the indicator...

Originally for mini special 20th edition which had 2 clock speedo cluster in front of driver and AAU3296 (ADO16)wing indicators.The special also had 1100cc engine. This front loom only has found its way on certain mini clubmans with corr...

Universal post type battery earth strap with clamp type fitting and correct length for most alternatives of batteries fitted.

This is the wiring short conversion loom that fits to the old central speedo and is used by people modifying from 2 or 3 clock dashes to single clock or just repairing damaged looms. With the correct bulb holders and spade fittings. Now uses 5x [link...

A plastic lamp spade connection with sidelight bulb aperture for use on sealed beam units only. Uses a GLB501 capless bulb. The mini clubman used sealed beams but had independant side lamps and therefore had an equivalent unit less the s...

The only battery cable to run the full length of the Mini, this has a positive type terminal that clamps arond the post rather than the helmet or cap type on much earlier cars. Some cars had slightly shorter cables than this but measure your old cabl...

Braided rear part loom ONLY for MK1 Minis without a rear heated screen.

Large grommet to fit 1"approx holes in bulkhead for items that need to be able to flex and move such as capillary tubes and oil pipes. 7/32" hole size.

The small hole will expand and is also used as wiring loom through bulkhead and battery c...

This plug fits the hole in the inner wing where the wiring for the wing side repeater lamp goes through the body on cars after 1986.

Sports coil for ballast resistor type ignition.

Best internal parts tested and another intermotor top product.

Its not the name on the outside but whats on the inside which matters.

Original type coil bracket 12G29...

Range of distributors with modern day curves specially built,programmed and tested for Mini Spares in UK.

Beware of the cheap China made units that we have tested and currently offered by other vendors that are poorly made with wrong setting...

original Lucas type RESIN BASED CONDENSER made for the 45/59D type distributor if you want a quality item rather than the cheaper inferior parts available. Filled with 3m of winding inside as per original Lucas but every copy analysed to date has ...

Screw for holding PRC1230A to the number plate light body, 1970 onwards.

Stainless steel screw kit for all mk2/3 lens to lamp body. Comes as a car set with six screws and six fibre washers.