£270.60 exc vat
£324.72 inc vat
In stock
£270.60 exc vat
£324.72 inc vat
In stockRecommended usage 1 x KC530M to fit one mini.
The Rover factory version of the original 649 grind as used in the Metro race challenge. On a new blank these are not always kept in stock now owing to price and usage but available to order within 2 weeks
Genuine Mini Spares camshaft for use with 1.5 rockers if preferred--below 5000rpm should produce more power than the 286 profile. Close to MDM274
Cam Timing
107 degrees at full lift on No1 inlet
SEAT...
Replace with new camshaft,it's almost too easy to overlook during a rebuild. Camshaft bearings are pressed into the block and thus are usually done by a machine shop. You would not rebuild an engine without replacing the rod bearings, so why not the ...
Hottest road usable cam. Not a good traffic cam. Lumpy idle. Not very suitable for small bore units unless fully prepared with big valve head. Very strong mid and top end power. Rev range 2,000 - 7,500 rpm.
See EVOLUTION001...
Converted into a non melting type grease.Favoured by proffessionals for camshaft,lobes and lifter,and any valvetrain to stop scuffing on start up. Also useful for oil pumps to stop drain back on start up
Lightened cam gear duplex timing gear and chain set. Not recommended for race/rally applications. approx 69-70g 9% lighter
General: Camshaft Drive Systems
For highly tuned engines always use steel duplex as cast is nowhere as st...
This is possibly the ultimate street cam. Also great for autocross or Vintage racing. Power band 2000-7000RPM.
The result is much better driveability in a very high performance cam. These Kent cams are sold outright, no exchange.
Standard weight, 44.00grams, follower with oil drain hole. Always check for wear and replace whenever a new camshaft is fitted. These are manufactured by the supplier to AE Hepolite the original engine components manufacturer and should be coated wit...
If you are replacing your timing chain or just doing routine maintenance a new locktab is sure to come in handy.
Adjustable cam gear set with non stretch chain. Cam gear weighs 674g
Even a stock camshaft needs to be timed correctly. If you want to get the maximum benefit from a "hot" cam it is doubly important that the cam timing be correct. This adju...
Timing cover front plate and tensioner plate bolt and washer kit. Comes with all parts to fit the cover except for the counter sunk screws if fitting a duplex kit (our duplex kits all come with these).
998cc flat top 3 ring circlip type piston set as fitted to early A plus to replace 4 ring set type. Gave 10.3 to1 CR and is a good alternative to use on any 998 with circlip type pistons. Replaced 4 ring(3 ring and scraper) P20754 from Hepolite 1980...
Water pump fitting kit for models without bypass facility, includes new bolts, washers and superseal gasket.
NON GENUINE for standard use only. These are the only type available at the moment and not as accurate as the original Rover product. The genuine factory pushrod was a very good product and does not need routine replacement. The strength and size of ...
The oil pressure relief valve consists of an aluminum plunger with a heavy spring behind it. Access is through the 15/16" domed cap nut beside the dizzy. Once this nut is removed the spring will be visible. The plunger is beneath the spring and will ...
Main bearings, 1275 2" mains. Heavy duty steel backed bearing for durability and long life. The bearings to use if you want it to last. The only bearings to use on a competition motor. Mahle manufacture..Quantity required-1 set.
Mahle was Vandervell bearings 1.064" 27.05mm wide mains for the late 850cc plus all 997/998/1100cc at 10 thou oversize. Early 850 mains were VP592 and 1.185" 30.10mm wide.
Ultra light non-adjustable steel duplex timing gear and chain set with locktab and countersunk screws AEA687.
See C-AJJ3325EVO with limited stretch race quality chain.
If you are working on your engine and ...
RING SET FOR 1275 STD. 4-RING PISTON. RING THICKNESS .0625 and 0.1562" oil rings.For later piston 19320 with 2 rings and an oil ring with the same ring sizes- keep the third ring as your second ring which should be of an oil scraper type, and usually...
Set of 8, original leyland ST product but now made for us to our specification. Critical to the life and performance of the camshaft is the use of high quality cam followers. Remember, they operate in a finite hole and thus the dimensional tolerances...
Standard size crankshaft washers as a set of four, fits 998 and 1100cc.
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.