£5.25 exc vat
£6.30 inc vat
In stock
£5.25 exc vat
£6.30 inc vat
In stockRecommended usage 1 x KHU10011 to fit one mini.
This is the rear bracket welded to the rear subframe for the later rubber strap mounted exhasts from late 1991 on use
2 reqd but sold seperately-From 1990 rover started fitting the hanging rubber exhaust mounting straps which push onto rods on the exhaust and rear subframe similar to the old metro. These were used right to the end of production on minis.
these bolt onbrackets were made to fit on the rear subframe when fitting the later type rubber hanging strap exhausts. this one fits on the front of the rear subframe.
cars from about 1991 on had these brackets welded in position
All the Nuts, bolts and washers you will need to fit a rear subframe to your car, less the support pins and bushes. These kits are aimed at those wanting to fit different rear subframe bushes such as the Poly bushes.
Complete set of bolts to mount the front subframe on all post 76 single bolt subframes less the large tower bolts and towing eye, enough fixings are supplied for those who wish not to use a towing eye.
Powder coated finish for longevity and looks. Don't forget to renew the bushes and bolts. These are pre 1990 Non Genuine subframes without the prongs for the later rubber exhaust. Adaptor brackets are available as C-ARA670/1 to enable fitment of late...
Rear subframe from original tooling as made for the factory but only with early
fixtures for hanging the exhaust (ie not the rubber hanger type from 1990 on)
but you can overcome this by using RC40 fitting kit as per or...
E coated Mini Spares product. Have a look at your subframe because if it looks bad then you need a new one for your MOT. Don't forget to renew the bushes and bolts.If you have the 1991 on type with mounting prongs for the exhaust rubber straps then y...
This is a budget way of improving the stability of the front subframe leaving the rear mountings standard for quietness.
It only includes the 4 poly tower spacers and for the front of the front subframe 2 poly spacers and 2 metal washers.
Minis Spares product to a slightly higher modern day shore hardness and texture soecification.
Pre 1976 used 8 of these bushes for the trunnions on the rear subframe but from (MK4)1976 on Rover reduced the quantity to 4 and used 2 larger bus...
To compliment the top alloy blocks (C-STR640), those troublesome front rubber mountings can be replaced by alloy cast mountings which will not break and further enhance roadholding. These are for the front of the front subframe on vehicles built from...
The set of four aluminum top front subframe mountings are to replace the standard rubbers fitted on vehicles from 1976 to present date. These alloy pads help reduce subframe movement, which is detrimental to handling when driven hard. As the original...
E coated Mini Spares product. This non genuine dry suspension subframe has the metal prongs/hangers for rubber strap type mounts as fitted from 1990 cars. Supplied in superb looking E-coat finish for longevity, with strengthening brackets as per MPI ...
Genuine correct length with cut outs and drain holes in the correct places.
The MK3 door seal is notable because of it's large 'bulb' area. The 'bulb' is the round section that the door closes against. The size is determined by how much gap ...
complete kit of bushes and bolts for pre 1976 rear subframes when 8 rubber bushes the same size are used--for cars after 1976 with 4 small and 2 large rubber bushes use MS43
Rubber mounts are made in the UK.
The Mini's rear subframe is rubber mounted. Polyurethane (stiffer, much longer lasting) bushes are now available for the rear subframe trunions. Cars manufactured before 1976 can use the same bush (2A5818/POLY) at the front and rear of the subframe, ...
The Mini's rear subframe is rubber mounted. Polyurethane (stiffer, much longer lasting) bushes are now available for the rear subframe trunions. Cars manufactured before 1976 used the same bush 2A5818(C-STR638) at the front and rear of the subframe, ...
Mini Spares product is a better quality pin-Please note that only the pin is supplied. Please see 2A5818MS for the bushes.
2 required per car
The correct screw for holding the 2A4267MS bump stop for the upper arm on the front suspension. 3/16"unf 1/2"long flat head phillips type screw.
Rear solid brackets for the front subframe of post 1976 models, ideal for racing or road if noise is not important. But very important if you are after the ultimate handling! we have tried the poly type but they were not as successful.
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.