£54.00 exc vat
£64.80 inc vat
In stock
£54.00 exc vat
£64.80 inc vat
In stockRecommended usage 1 x TRAN0005 to fit one mini.
New Minispares Evolution straight cut crownwheel and pinion set 3.47. The crownwheel in these kits has a 20% wider gear than previously supplied, and a pinion made from Aero quality steel making it 20% tougher.17x59 teeth count.
Always Check...
Mini Spares own Evolution limited slip diff with over 10 years success
No serious competitor would use a Mini on a race track or autocross course without a limited slip differential should the rules allow it. This original Mini Spares Ev...
Hardened flat washer to be used with flange type LSD Hardy Spicer C-BTA1262 outputs.
The 45/45 is best for forest and rallying in general but if on tarmac a rally diff with a different ramp 45/90 TRAN0004 can be made to special order, the road diff is good for tarmac also.
The gearbox diff side plate bonze colour bush for all except auto and cooper S with hardy spicer output shafts. Sold singly 2 required per gearbox.
clearance needs to be 0.03mm
This is an aftermarket high tensile shouldered bolt that engine and gearbox tuners are using, as the original shape head and high tensile type bolt is no longer available. For holding the crown wheel to the differential housing.
Sold individ...
Minispares own Evolution limited slip diff with over 10 years success
General spec and design is the same as C-AJJ3387 but has a 45/45 ramp type giving drive on acceleration and deceleration, preferred by many rally drivers for ...
REPLACEMENT CLUTCH PLATE PACK KIT FOR MINISPARES EVOLUTION LIMITED SLIP DIFFERENTIAL
4 are required for the drive flange to 8.4" disc set ups and is also the same bolt for limited slip diff crownwheels. 3/8" UNF THREAD 11/16" long.
Sold singly
Outputs for LSD when using inboard CV joints. Sold single with 2 needed per car.
Originally developed by Rover to cut down on warranty hourly costs on powertrain warranty repairs, by their main dealers.-Labour time allowed at Rover dealers for fitting this seal was 3.4 hours labour rate.
This is a special rigid seal and ...
Idler gear conversion for straight cut drop gearsets only.
This set up is for A plus idler gearbox cases only and uses a single roller bearing centrally unlike the old timken conversion which had taper bearings either end.
Minispares were the first company to produce these layshafts for performance engine/gearboxes as the standard type would flex and resullt in the breakage of the bearings causing seizure. Produced in an upgraded material and heat treated to the correc...
Straight cut teeth broach gear for the 1st motion shaft which runs with the straight cut idler and primary gear combinations. This has 23 teeth and one identification ring on actual teeth.
Achievable drop gear ratios ...
This is the large clutch case gasket that is made to a special thickness.
Many companies who copy these gaskets are not aware that the gasket thickness and consistency is important as it affects the clearance on the idler gear shimming. This...
Evolution Straight cut 24 tooth input gear. Usually has 2 identification rings on gear teeth.
Achievable drop gear ratios when using our Evolution gears:
22 tooth primary - 30 tooth idler - 25 too...
Gearbox output shaft housing gasket for all minis except auto.
Sold singly 2 required per gearbox.
This is our racers favourite way of dealing with the worn or troublesome front primary gear bush.(this is NOT the top hat type rear bush)22.5mm wide. Racers and professional engine builders will use their own tolerances but these are set for road use...
Genuine Mini Spares latest state of the art Klinger material gasket, replacing 22A2237B for the clutch housing to help prevent oil leaks.
Measures 31 thou or 0.81 mm thick but compresses to correct size when fitted. Using l...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.