($1.00) £1.00 exc vat
($1.20) £1.20 inc vat
Out of stock
special sized nut for this purpose 15/16" wide with 5/8" centre. See also 2K8686 for left hand side which has one flat machined side.
($1.00) £1.00 exc vat
($1.20) £1.20 inc vat
Out of stock
This special shake proof washer should be replaced. Found on front hose.
Also used on 21A1524 hydrolastic pipe adaptor.
One side of this nut is machined flat to go against the subframe body where it holds the brake hose in place. There is a shakeproof washer WE600101 fitted first against the machined side. On the assembly line the factory fitted this nut ...
12" wheel to 10" wheel running gear conversion kit. Less wheels.
This kit will convert your 8.4 disc set up to the Cooper S 7.5 discs to allow fitment of 10" wheels, kit includes discs, calipers, kevlar pads with split pins and drive flanges...
Flanged head short UNC 5.16" BOLT for flywheel casing 1.0625"long it was used as an alternative to DAM7755 which was only 1" Long with tuflock patch to secure-this will be discontinued by Rover when current stocks are gone.
A pair of 7.5" brake discs and one set of Kevlar road brake pads.
Single line L/H/D with servo-dry suspension. If you have a drum brake mini then this kit will require 2 front wheel cylinder to wheel cylinder pipes HF10
BRIDGING BOLTS AND SEAL FOR BETWEEN THE TWO CALIPER HALVES ON 7.5" COOPER S CALIPERS. Should be torqued to 37/38Nm.
Adjustable original brake proportioning/balancing valve for racers only.
The most common brake system on the Mini has Disc brakes in the front and drums in the rear. The weight bias on the car is all in the front and thus under hard braking...
Easy bend copper 12" brake pipe with 2 male ends for single line master cylinders---for clutch or brake on early minis but the longer HF14 might be easier for the brake master which was nearer 13" long. These kits or pipes are at least 3...
Front to rear brake line kit for cars from 1988-2000 with the factory Servo incorporated into the brake master cylinder. You'd think that the way Minis leak oil they'd never rust on the underside, but they do! If your Mini is rusty below it is a good...
From 1989 minis which have the brake servo built into the master cylinder and it is very difficult to work in the engine bay, especialy clutch changes because of the extra room taken up by this dual cylinder. By replacing the 2 metal brake pipes from...
UNION FOR BRAKE PIPES IF YOU HAVE A DO IT YOURSELF FLARING KIT.
Minispares own product-L/H, to last Rover drawings and supplied to us by a UK Heritage specialist. Originally the BMC castings were machined by Portland Engineering but in the 90's we put down tooling with IVRA/Italy who had them manufactured by Torm...
Male metric brake union as used on front to rear PDWA valve and later master cylinders. Pipes should be double flared.
If your rear brake drums have 1" built in spacers such as all Cooper S and any post 1984 minis, these are the longer drum retaining screws, 2 required per drum and sold individually.
Easy bend long life copper brake pipe with 2 male ends and ideal and best replacement for the original 16" pipe from the 3 way union to the brake switch on single line dry suspension minis. These kits or pipes are at least 35% off retail.
Easy bend copper 24"long brake pipe with one female and one male end for the regulator on the rear subframe to the n/s/r hose on hydrolastic cars only.
Also used on split front to rear system with valve in engine compartment - from 3 way uni...
These repair kits are for the later twin leading front drum brakes wheel cylinders GWC126/7 with .9375" bore size. The earlier twin cylinder set up used part number 8G8816 for GWC102/3 with 0.8125" bore size.
Correct size and length brake pad pin for the caliper using 7.5" disc size as fitted to Cooper S and 1275GT. 4 required for 1 car, also fits Cooper 7" calipers. 3mm diameter.
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.