GEARBOX TO BLOCK STEPPED WASHER FOR CORNER BOLT

($4.80) £4.80 exc vat

($5.76) £5.76 inc vat

GEARBOX TO BLOCK LOCATING DOWEL (HOLLOW)

12H1824

($4.80) £4.80 exc vat

($5.76) £5.76 inc vat

ENGINE TO GEARBOX NUT AND BOLT KIT

MSSK060

Complete nut, bolt and washer set for engine to gearbox only

($3.50) £3.50 exc vat

($4.20) £4.20 inc vat

BOLT OIL FILTER HEAD TO BLOCK

LYG10008

later cars used this bolt to hold on the spin on filter head to the block-earlier cars used the CHS2613 stud--both are interchangeable

3/8"unc 1"long

($2.10) £2.10 exc vat

($2.52) £2.52 inc vat

ALTERNATOR BRACKET PILLAR

12G289

Special bolt that fits the engine front plate to support the adjusting link for alternators/dynamo

($9.93) £9.93 exc vat

($11.92) £11.92 inc vat

CUP WASHER FOR TAPPET CHEST GROMMET

12A1177

The special washer under the tappet cover bolt.Sold singly 2 required per engine.

See 12A1176 for seal

($0.80) £0.80 exc vat

($0.96) £0.96 inc vat

OIL PUMP BOLT CONCENTRIC/TURBO. SEE NOTES.

BH604141

1.75" LONG shouldered 1/4" bolt fits original concentric pumps plus some GLP139 and GLP110MS - check that you need a bolt this length as many later pumps require shorter bolts. This can of course be cut down or see [link]BH6...

($0.83) £0.83 exc vat

($1.00) £1.00 inc vat

ROCKER STUD LONG 3" x 5/16" UNC

51K885

Using new hardware makes any job more pleasant. If you're servicing your cylinder head you should examine the rocker studs for signs of stretching or stripped threads. Two long (51K885) and two short (51K1473) per head.

This is ...

($1.25) £1.25 exc vat

($1.50) £1.50 inc vat

DRAIN PLUG ENGINE BLOCK REAR WATER DRAIN OFF

53K2853

Fitted to the rear of engine blocks to drain out water these are now obsolete from Rover but available from us.1/4"bsp

($5.90) £5.90 exc vat

($7.08) £7.08 inc vat

NEEDLE ROLLER 1ST MOTION / LAYSHAFT 4 SYNC

13H9513INA

High quality version of 13H9513, INA branded.

Dual use bearing fits the end of the A Plus 18mm mainshaft where the 1st Motion shaft slides on, plus it is used on the A Plus layshaft smaller end.

Kno...

($15.63) £15.63 exc vat

($18.76) £18.76 inc vat

CRANK THRUST WASHER SET STANDARD 998

ACL2122

Set of standard size 998 thrust washers.

($9.75) £9.75 exc vat

($11.70) £11.70 inc vat

ACL SMALL BORE ENGINE CAM LINER SET

ACL3046

Replace with new camshaft,it's almost too easy to overlook during a rebuild. Camshaft bearings are pressed into the block and thus are usually done by a machine shop. You would not rebuild an engine without replacing the rod bearings, so why not the ...

($16.14) £16.14 exc vat

($19.37) £19.37 inc vat

11/16" DOWTY SEAL

DSM18

11/16" dowty seal for post 1991 cars where the original pipe has been replaced with a braided pipe or an oil cooler has been fitted using part number MOC4. used on the TCZ102

($2.40) £2.40 exc vat

($2.88) £2.88 inc vat

SWIFTUNE PERFORMANCE DIE CAST PISTON SET 1275 +20

C-STN103-20

These Swiftune die cast performance pistons are part of their new Heritage range and are manufactured by global leading German F1 piston manufacturer Mahle. These pistons have been developed using their 50 plus years of experience.

Glyn Swif...

($299.00) £299.00 exc vat

($358.80) £358.80 inc vat

PRIMARY GEAR BACKING RING GENUINE

88G549GENUINE

Genuine Rover spacer that fits up against the primary gear on the crankshaft and held on by the "C" washer 22A319 - both these parts wear as well as the gear.

Mini Spares also produce a ring 2 thou thicker 88G549 to...

($13.00) £13.00 exc vat

($15.60) £15.60 inc vat

DIFF HOUSING LOCK TAB ROD CHANGE LH

42H500

Left hand differential lock tab as used on rod change boxes up until 1982 when they were not longer used. For R/H locktab see 22A962

($0.91) £0.91 exc vat

($1.09) £1.09 inc vat

DIFF HOUSING LOCK TAB ROD CHANGE RH

22A692

Right hand differential lock tab as used on rod change boxes up until 1982 when they were not longer used.

($1.35) £1.35 exc vat

($1.62) £1.62 inc vat

MINI SPARES COMBINED BLOCK/GEARBOX GASKET AND SEAL...

AJM100MS

Mini Spares best quality complete gasket and seal kit for engine block and gearbox,for all common engine types and sizes.

Also comes complete with Mini Spares Evolution clutch oil seal 13H2934MS, differential oil seals...

($26.00) £26.00 exc vat

($31.20) £31.20 inc vat

MAINS SET +10 PRE A PLUS/EARLY A+ 1275 ACL

C-AEM91120-10

ACL Race Bearings

ACL Race series bearings are precision manufactured to a wall thickness of ±0.0040mm giving engine builders close control of vertical oil clearance.

What is the purpose of ACL Race series bearings?
...

($74.51) £74.51 exc vat

($89.41) £89.41 inc vat

BIG ENDS 1300 STD SIZE EXCEPT COOPER S ACL RACE

C-AEB91306-00

ACL Race Bearings

ACL Race series bearings are precision manufactured to a wall thickness of ±0.0040mm giving engine builders close control of vertical oil clearance.

What is the purpose of ACL Race series bearings?
...

($69.06) £69.06 exc vat

($82.87) £82.87 inc vat