($45.00) £45.00 exc vat
($54.00) £54.00 inc vat
In stock
Beware of the cheap China made units that we have tested and currently offered by other vendors that are poorly made with wrong settings. See note at bottom
GEU930 25D 850/early 998
12G2140 23D Cooper S non vac
BAU1962 45D 998/1098
ADU5789 59D 998 A plus
12G4180 45D 1275cc with vac, good for modified road tune engines
ADU3825 59D 1275 with vac, A Plus good for modified road tune.
For electronic versions add suffix MS- example= ADU5789MS.
Mini Spares specification for best alround performance electric distributor for std to 276 camshaft profiles see C-27H7698
Distributor drive spindle if required is 12G3560
Distributor clamp plate is TAM1671
Bolt for clamp is TAM1706 A Plus 59D for any 1275cc with vac unit for modern day fuel and mildly tuned engines. For best performance and tune we advise our electronic evolution version C-27H7701
Curves and advance for modern day poor petrols. Distributors can 'work' long past their useful life! These are priced to help save money on rebuilds with a vac unit fitted to compliment modern day fuel and timing, unlike all previous types available which never fulfilled engine potential. If you want to get the most from the performance of your engine a very good distributor is a must! good for any metro 1275cc engine in a mini or metro--See ADU3825MS for electric type without contact breakers.
DODGY DISTRIBUTORS
We’ve seen distributors with all different curves in the same batch. Base plates
that stick and alter the curves, sometimes jamming in full advance. When tested
we had difficulty getting them to run correctly when using a timing light and we
found that the rotor arm and dog at the bottom of shaft was often out of phase
putting the rotor arm in wrong position in relation to the point at where the spark
fired. We also found rotor arms that were hard up against the carbon bush in the
top of distributor cap causing the cap to burn away in middle.
Having tried and tested countless suppliers of imported and British made
distributors we had all ours individually built and tested to prevent costly engine
failures and breakdowns for the following reason - those suppliers were unable
to advise what curves were in them - we rarely found them the same in any
batch! Every part, even so-called ‘Mini Spares branded parts’ are being copied
for financial gain as Minis climb in popularity and value. Unscrupulous
companies can get parts made cheaply overseas, but they lack the technical
knowledge and precision required to make them correctly
($45.00) £45.00 exc vat
($54.00) £54.00 inc vat
In stockRecommended usage 1 x ADU3825 to fit one mini.
the bolt that holds distributor clamp TAM1671 in the block on A Plus engines
now obsolete use 3/8"unf bolt with thread length of 1"
A Plus Electronic Ignition distributor with vac unit, modified to our spec in UK to give best performance on any minis with std to 276 camshaft profile.
Ideal for our EVOLUTION001 camshaft
Brand New distributor complet...
Negative earth A Plus 59D for any 1275cc with vac unit with modern day driving curves and petrol avaiable.
For best performance and tune we advise our electronic evolution version C-27H7701
Distributors can 'work' lon...
Timing cover front plate and tensioner plate bolt and washer kit. Comes with all parts to fit the cover except for the counter sunk screws if fitting a duplex kit (our duplex kits all come with these).
Fitting kit comprising of studs, nuts, plain washers, spring washers and a gasket
This kit of head studs is the best available for road and lightly tuned engines. See the C-AHT280 set for highly tuned engines.
The material spec is alloy steel heat treated to 75 tensile tons per square foot minimum and finish...
Stabiliser bush kit for lower engine steady
Mini Spares best quality complete gasket and seal kit for engine block and gearbox,for all common engine types and sizes.
Also comes complete with Mini Spares Evolution clutch oil seal 13H2934MS, differential oil seals...
ACL Race Bearings
ACL Race series bearings are precision manufactured to a wall thickness of ±0.0040mm giving engine builders close control of vertical oil clearance.
What is the purpose of ACL Race series bearings?
...
Sports coil for ballast resistor type ignition.
Best internal parts tested and another intermotor top product.
Its not the name on the outside but whats on the inside which matters.
Original type coil bracket 12G29...
Pre A Plus Electronic Ignition distributor with vac unit, modified to our specification in the UK to give best performance on any minis with std to 276 camshaft profile.
Brand New distributor complete with electronic conversion already fitt...
Lots of things have been written about performance plug ignition wires but regardless of what you believe we all know that good wires are a must. This special competiton wires set from the Lucas factory has 8mm wire and the highest performance, no br...
UK made-EN24T allen key head extra strong 5/16"unf rocker adjusting screw, original screws are often worn but rarely inspected, both ends of this complex screw are often worn and in dire need of replacement. Most available on the market are imported ...
Wiper Swithch MK1/2/EARLY MK3 blade type switch for using to convert to 2 speed wipers when current 2 speed wiper motor is used.
Set of 4 ignition leads from the original supplier to Unipart, suitable for all twin point minis 1997 onwards. For use with M4 type coil.
MPI only. 3 YEAR GUARANTEE-UK made.Large impeller higher capacity water pump. Mini Spares procured product as original Rover Airtex tooling has been scrapped.
Fitted with a PPS, glass filled plastic impeller as used by Jaguar and Aston Marti...
3 YEAR GUARANTEE-UK made.Large impeller higher capacity water pump with top quality die cast body . Mini Spares procured product as the original superb Rover Airtex tooling has been scrapped.
Fitted with a PPS, glass filled plastic impeller...
3 YEAR GUARANTEE-UK made. Large impeller higher capacity water pump with a high quality die cast body. A Mini Spares procured product as the original superb Rover Airtex tooling has been scrapped.
Fitted with a PPS, glass filled plastic impe...
Negative earth A Plus 59D for any 1275cc with vac unit with modern day driving curves and petrol avaiable.
For best performance and tune we advise our electronic evolution version C-27H7701
Distributors can 'work' lon...
Ultra light non-adjustable steel duplex timing gear and chain set with locktab and countersunk screws but with a 2H4905EVO limited stretch race quality chain.
If you are working on your engine and you want to do it right then yo...
Chrome fittings for rocker covers. Kit includes 2 of, rubber seals, chrome washers and spacers.1 kit required per engine.
these are the best quality chrome parts we could find in the market
original Lucas type RESIN BASED CONDENSER made for the 45/59D type distributor if you want a quality item rather than the cheaper inferior parts available. Filled with 3m of winding inside as per original Lucas but every copy analysed to date has ...
NEGATIVE EARTH ONLY..Reproduction CONTACTLESS Distributor suitable for modern day fuels for 850 and 998cc pre 1974 with upgraded rotor arm "Negative earth only". A worn out distributor can cost you both performance and economy. Precise spark timing ...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.