DISTRIBUTOR CAP FOR 123 ELECTRONIC DISTRIBUTOR
GDC123

(21,00 €) £21.00 exc vat

(25,20 €) £25.20 inc vat

In stockIn stock
If you have a new 123 ELECTRONIC distributor this is the replacement cap.

For earlier 123 distributors please see part number GDC123E.

Rotor arm is GRA123

(21,00 €) £21.00 exc vat

(25,20 €) £25.20 inc vat

In stockIn stock

Recommended usage 1 x GDC123 to fit one mini.
Distributors - Qty 1

People also bought products

Electronic Distributor for any standard A+ 998cc. Negative earth only.



From 1982on 998cc were fitted with a ballast coil which means a new wire must be fitted from fusebox top left terminal where there is a large white cable to the...

The all new 123 Electronic distributor is now available at Minispares. Featuring 16 ready programmed switchable advanced curves built in as standard, a must for any mini with a worn distributor. Full instructions are included with the system. For an...

If you want to tune your engine, or you have an engine for which there is no standard distributor available.....the new 123\TUNE is the answer ! By connecting it to a computer, the end-user can easily adapt the 123\TUNE to fulfill even the most deman...

the oil seal to fit on 12A1136 distributor housing. Pre A Plus

the earlier housing 2A612 did not have a seal.

If you have an original 25D type distributor this is an upgraded arm (blade moulded and riveted )for performance use because all the other types available now are likely to fail at high revs. Because the blade is thin,or the rivet sometimes to long a...

The all new 123 Electronic distributor is now available at Minispares. Featuring 16 pre programmed advanced curves built in, a must for any mini with a worn distributor. Full instructions are included with the system. For any A series, A Plus engines...

The all new 123 Electronic distributor is now available at Minispares. Featuring 16 ready programmed switchable advanced curves built in as standard, a must for any mini with a worn distributor. Full instructions are included with the system. For any...

The all new 123 Electronic distributor is now available at Minispares. Featuring 16 ready programmed switchable advanced curves built in as standard, a must for any mini with a worn distributor. Full instructions are included with the system. For an...

The all new 123 Electronic distributor is now available at Minispares. Featuring 16 ready programmed switchable advanced curves built in as standard, a must for any mini with a worn distributor. Full instructions are included with the system.For any ...

The O ring that actually sits on the distributor drive spindle shaft in the recess provided.

The stock vacuum advance distributor is connected to the carb/manifold by a small rubber joint that in turn is mated to metal line that fits the distributor. If the little rubber connector is deteriorated it could allow a vacuum leak at the carb and ...

This "Pigtail" wire is all that carries current through the distributor to the points.Fits 23 and 25d type distributors

originally fitted to 1976-45D type distributors and 41824 distributor that fitted mainly 998/1100cc plus allegro and maxi a real jack of all trades we have found this works on all small bore engines with our new range of 45 and 59d distributor curve...

Originally a red cap but now supplied in black, it was only fitted to Ducellier type distributors which were fitted to Mini Metros plus a few 998cc minis.Contact set is GCS119 and the condenser is GSC2113. Rotor arm is [lin...

Prong type clamp that bolts to the block and retains the A plus distributor in place. The screw is TAM1706.

Pre A plus clamp is 501134

for 23/25D distributor but see [link]47H5250[/link} for resin type upgrade with 3m of wire as opposed to every aftermarket type analysed with only 1.5m of wire.

its worth paying extra for the condenser and rotor arm [link]GRA101]/link]

Fited to Lucas type distributors with 45D body in 1974 until 1990 when electronic type that was held on by 2 screws appeared as oppossed to this clip on this type. If you need a new distributor clip-we have them as GDC136CLIP.

this is the original mini distributor cap where the leads were secured by screws and was fitted to the 25D range of lucas distributors. This cap had side entry leads [link[GHT101]/link] and is now only available from one or two manufactures owing to ...

Lots of things have been written about performance plug ignition wires but regardless of what you believe we all know that good wires are a must. This special competiton wires set from the Lucas factory has 8mm wire and the highest performance, no br...

best plug for 12g295 head as fitted to 998 cooper--for tuned head use B7ES.

this is good for any head where a lot has been machined off-flat top pistons.