(90,00 €) £90.00 exc vat
(108,00 €) £108.00 inc vat
Out of stock
RACE quality bearing set being made at the Mahle Motorsport Race Bearing Division Vandervell F1 plant in the UK...
(90,00 €) £90.00 exc vat
(108,00 €) £108.00 inc vat
Out of stock
These con rod bolt and nut set are made by ARP in the USA and considered the best available FITS 1300 con rods plus MGB late 18V engine numbers with 11-32" bolts. Quantity required one kit per car. torque up to 38-40lb ft.
Genuine part on sale at less than half price.
Most engine builders will tell you to replace the rod bolts as often as you can afford, but at least every other time you do the bottom end. If you don't know the last time, replace them. The [li...
Multi point big end journal nut for 1.75" bearing size con rods. These are multipoint nuts as fitted to Pre A plus engines. A Plus engines used CAM6263 which had the built in flange to spread the load but are not available. They are in...
ACL Race Bearings
ACL Race series bearings are precision manufactured to a wall thickness of ±0.0040mm giving engine builders close control of vertical oil clearance.
What is the purpose of ACL Race series bearings?
...
You should replace the camshaft bearings every time the block goes to the machine shop. These bearings fit all 1275cc blocks plus 970 and 1071 Cooper S. It's almost too simple and thus often overlooked during a rebuild. Camshaft bearings are pressed...
Mahle RACE quality +10 size main bearings for A Plus 1275cc only as used by competition engine builders..Quantity required-1 set.
RACE quality bearing set being made at the Mahle Motorsport Race Bearing Division Vandervell F1 plant in the ...
Mahle RACE quality std size shells as used by competition engine builders.
For 1.625" big ends on 998 and Cooper S.
RACE quality bearing set being made at the Mahle Motorsport Race Bearing Division Vandervell F1 plant in the UK. Th...
Mahle RACE quality std size shells as used by competition engine builders.
for 1.75" big ends on 1275cc.
RACE quality bearing set being made at the Mahle Motorsport Race Bearing Division Vandervell F1 plant in the UK. This is an up...
Main bearings, 1275 2" mains. Heavy duty steel backed bearing for durability and long life. The bearings to use if you want it to last. The only bearings to use on a competition motor. Mahle manufacture..Quantity required-1 set.
Big end shell bearings for the 1275 larger 1.75" diameter rod pin-not Cooper S
( Tri-Metal )
Sintered copper lead, lead plated,steel backed
Nominal Composition
Copper 74%
Lead 24%
Tin ...
Rod bearings, 850-1275 1 5/8" journals. Heavy duty steel backed bearing for durability and long life. The bearings to use if you want it to last. The only bearings to use on a fast road car.
( Tri-Metal )
Sintered copper lead, lead...
Rod bearings, 850-1275 1 5/8" journals. Heavy duty steel backed bearing for durability and long life. The bearings to use if you want it to last. The only bearings to use on a fast road motor.
( Tri-Metal )
Sintered copper lead, le...
NON GENUINE for standard use only. These are the only type available at the moment and not as accurate as the original Rover product. The genuine factory pushrod was a very good product and does not need routine replacement. The strength and size of ...
Low drag 1275 piston standard size 2.780 plus 20 thou oversize(Rings included).
This piston has a possible compression ratio of 10.3:1 as fitted to Cooper RSP 1990.
The best performance 1275 pistons are C-STN100 range which have 9.7...
Genuine Mini Spares Klinger timing chain gasket for any BMC A series engine with 10 gasket holes, fitted until the introduction of the A plus type which had a bulge in its side where the tensioner was fitted which had 11 holes.
The klinger m...
A must if you want to run a mechanical oil gauge and retain the oil warning switch. Screws straight into the block on all A series engines.
3mm OIL RING with compression ring size .0591" (1.5mm)and one piece oil ring .1181" (3mm)on p21253 pistons giving 9.7cr on 1275cc. 60 thou oversize
Rover piston were stamped 21963 for high compression but 21962 seems to be stampe...
Favoured by proffessionals for press fitting pistons, pre lubing bushes, roller and plain bearings, journals and gears. Prevents scuffing, seizure, wear, rust. Waterproof and corrosion proof.
Genuine Mini Spares green and black upgraded Klinger gasket set. 3 pieces
Has the extra front gasket required for 3 synchro case use
Genuine Mini Spares Original black timing cover oil seal for all A series until the introduction of a new type of lip seal introduced in 1991 mainly for injection engines, when they changed to LUF10006--albeit many owners fit this not kn...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.