CLUTCH PUSH ROD
13H396

£2.70 exc vat

£3.24 inc vat

In stockIn stock
The push rod on your clutch arm held in by clevis pin CLZ518 that goes into the slave cylinder. Check the eyepiece for wear.

The same push rod was fitted to both Verto and Pre verto slave cylinders.

£2.70 exc vat

£3.24 inc vat

In stockIn stock

Recommended usage 1 x 13H396 to fit one mini.
Diaphragm Clutch & Slave Cylinder - 1964 ON - Qty 1
Verto Clutch & Slave Cylinder 1982 ON - Qty 1
Clutch Housing - Qty 1
Flywheel and Clutch - Qty 1

Recommended products
CLUTCH LEVER ARM TOP CLEVIS PIN
CLZ518

Upper clutch lever arms clevis pin, suitable for both verto and non verto arms.

Split pin for common clevis pin list

GFK101 for CLZ409 handbrake levers to cable on rear drum

GFK102 mos...

£1.14 exc vat

£1.37 inc vat
SPLIT PIN FOR MINI CLEVIS PINS (EXCEPT HANDBRAKE)
GFK102

Universal split pin for all mini clevis pins, except handbrake lever.

Split pin for common clevis pin list

GFK101 for CLZ409 handbrake levers to cable on rear drum

GFK102 most mini cle...

£0.12 exc vat

£0.14 inc vat
Kit products
CLUTCH ARM FITTING KIT FOR 22A2204
22A2204FK

Fitting kit for 22A2204MS clutch arm with a square end. The plate to fit on the end of the arm in this kit is 20mm wide at both ends see 2A3601MS but earlier arms used 25mm down to 20mm wide see 2A3601.
<...

£15.92 exc vat

£19.10 inc vat
People also bought products
EN24T PRE VERTO FLYWHEEL BOLT AND KEYWAY
22A747EVO

Pre verto flywheel bolt and keyway washer in EN24T



The bolt is CNC machined from stock EN24T steel with extra attention to the radius under the head to maximise strength.

£33.79 exc vat

£40.55 inc vat
CLUTCH ARM FITTING KIT FOR 22A2204
22A2204FK

Fitting kit for 22A2204MS clutch arm with a square end. The plate to fit on the end of the arm in this kit is 20mm wide at both ends see 2A3601MS but earlier arms used 25mm down to 20mm wide see 2A3601.
<...

£15.92 exc vat

£19.10 inc vat
CLUTCH RETURN SPRING ANCHOR FOR MINISPARES LEVER A...
2A3601MS

Plate on the end of the PRE A plus long type clutch arm 22A2204MS to hold the return spring 1G5999. The clevis pin to hold this on the arm is CLZ518--this is the square type but for earlier tapered type Rover ar...

£4.28 exc vat

£5.14 inc vat
FLANGED BOLT 5/16" UNF 1.75" LONG. CLUTCH CASE TO ...
DAM7758

Clutch housing bolt to engine long 5/16" UNF 1.75" long with tuflock patch to secure. Earlier bolts less tuflock are {link]BH605141{/link}

£0.83 exc vat

£1.00 inc vat
FLYWHEEL CASING BOLT WITH THREADLOCK 5/16unc x 1.0...
DAM7756

Flanged head short UNC 5.16" BOLT for flywheel casing 1.0625"long it was used as an alternative to DAM7755 which was only 1" Long with tuflock patch to secure-this will be discontinued by Rover when current stocks are gone.

£0.87 exc vat

£1.04 inc vat
CLUTCH OIL SEAL MINISPARES PERFORMANCE USE TYPE.
13H2934MS

Introduced for competition engines where the increased rev limits or temperature can cause the LUF10005 or 13H2934 to leak, this fits all minis except automatic. This is Mini Spares copy of the original gaco seal and is iden...

£3.55 exc vat

£4.26 inc vat
FLYWHEEL BOLT PRE VERTO
22A747

The bolt that holds the flywheel to the crank on cars with a diaphragm type clutch. Locked in place by 22A1155 locktab on the 88G508 key washer.

£8.74 exc vat

£10.49 inc vat
CLUTCH FLYWHEEL STRAP BOLT SHORT-torque to 16lbs o...
2A3659

There are 3 of these shorter 5/16"unf bolts holding the spring straps 2A3658 to the flywheel on diaphragm type flywheels only. Not for Verto flywheel.

Only tighten up to 16lbs per sq foot torque when using shake proof washer or ...

£1.85 exc vat

£2.22 inc vat
CLUTCH SEAL PROTECTOR SHIELD-FITTED TO VERTO CLUTC...
DAM2821

When the verto clutch was introduced the factory started fitting this plastic protector over the clutch oil seal on Metro's. It then apeared on injection minis with LUF10005 clutch seal to the end of production. Should be replaced when s...

£3.00 exc vat

£3.60 inc vat
CLUTCH BOLT LONG COVER TO PRESSURE torque to 16lbs...
2A3657

Shouldered 5/16"unf bolts for the Mini clutch backplate to the diaphragm, not for heavy duty use or racing. Only tighten up to 16lbs per sq foot torque when using shake proof washer (GHF323) or 18lbs if using flat washer and locktite. Only use [link]...

£2.09 exc vat

£2.51 inc vat
BRAKE MASTER CYLINDER GASKET - DUAL MASTER CYLINDE...
31G840

Gasket used under the dual master cylinder brake master cylinder. For the earlier single line brake pipe system see 31G279.

£0.96 exc vat

£1.15 inc vat
CLUTCH RETURN SPRING
1G5999

Clutch arm return spring for the return of the slave cylinder push rod. Total length 90mm.

£1.50 exc vat

£1.80 inc vat
FLYWHEEL KEYWAY - PRE VERTO (MADE IN EN24T STEEL)
88G508

Made in EN24T for strength they have been made to fit the majority of flywheels that seemed to slightly differ from the mid 60s. Run a file down the raised keyway if tight. This flywheel locking plate is for pre verto diaphragm clutches. For Verto ty...

£8.63 exc vat

£10.36 inc vat
VERTO RELEASE BEARING RETAINING O RING
AAU2866

"O"RING FOR A+ verto clutches only

£0.60 exc vat

£0.72 inc vat
CLUTCH RETURN SPRING ANCHOR FOR GENUINE CLUTCH ARM
2A3601

This plate is on the end of the PRE A plus original long type clutch arm 22A2204 to hold the return spring 1G5999. The clevis pin to hold this on the arm is CLZ518.

If you have the later Mini Spares arm...

£4.28 exc vat

£5.14 inc vat
CLUTCH PLUNGER - PRE VERTO (Round End)
22A180MS

Clutch release plunger-This is the carrier that holds the clutch release bearing and on the other end has a hole for the clutch lever arm 22A2204MS.

If you are looking for a Mini Spares upgraded product see 22A180.

£7.43 exc vat

£8.92 inc vat
WASHER COPPER BRAKE/CLUTCH UNION
3H550

1.4mm thick copper washer for all clutch and brake joint uses. This washer is 17.4mm wide with an 11.4mm diameter hole. Larger than a 233220A.

£0.50 exc vat

£0.60 inc vat
CLUTCH MASTER CYLINDER GASKET
31G279

This gasket sits under the clutch master cylinder.

For brake master cylinders see 31G840.

£0.80 exc vat

£0.96 inc vat
CLUTCH THROW OUT PLUNGER LARGE NUT
22A427

The large special shape nut on the adjusting end of the clutch plunger which holds the release bearing. The flat locking nut for this is NT610041. need a 15/16 spanner

£7.50 exc vat

£9.00 inc vat
CLUTCH OIL SEAL UPTO 1992
13H2934

See 13H2934MS for original silicon type best seal available, which is Mini Spares own copy of the original Gaco seal that was discontinued. These were the seals used on production/rally /race cars that never gave problems.

This ...

£1.85 exc vat

£2.22 inc vat